Egnition lock Examination This area contains SRS parts* 1. Disconnect the negative battery cable. 2. Remove the driver's side lower dashboard cover. 3. Disconnect the 5K connector from the under-panel fuse and relay box and the 7K...
Headlights and lamps Checking the headlight combination switch 1. Remove the driver's side lower instrument panel cover and steering column cover. 2. Disconnect the 4K and 7K connectors from the switch. 3. Inspect the connector and...
Headlights/Front Parking Lights/Turn Signal Lights Replacement Warning: Halogen headlights become very hot, so do not touch them or their connecting parts immediately after turning them off. 1. Remove the front bumper. 2. Remove the mounting bolts. 3. Disconnect each...
Side turn signal lights/license plate lights Replacement Side turn signal light: 1. Press the lock spring and remove the side turn signal light. 2. Disconnect the 2K connector from the flashlight. Number plate light: 1. Remove the two screws from the license plate...
Hazard/Turn Signal System Checking the Hazard Switch Caution: Be careful not to damage the hazard warning switch or center output panel when removing the switch. 1. Pull the switch out of the center output panel. 2. Disconnect the YuK connector...
Rear fog light Checking the switch Caution: Be careful not to damage the rear fog light switch or center output panel when removing the switch. 1. Pull the switch out of the dashboard. 2. Disconnect the 8K connector from the switch....
Internal equipment Checking the fuel level indicator/sensor Warning. Do not smoke while working on the fuel system. Keep open flames away from your work area. 1. Before starting the test, check fuse No. 25 (7.5A) in the under-panel fuse...
Rear window defroster Checking the input signal, switch (with timer) Attention. When pulling out the switch, be careful not to damage the rear window defroster switch or the center panel. Note: before starting the test, check if fuse No. 16...
Controllable mirrors Functional check Attention. When pulling out the switch, be careful not to damage the mirror switch or the driver's side lower dashboard cover. 1. Pull the switch out of the driver's side lower dashboard cover. 2....
Checking the input signal of the folding mirror control unit 1. Disconnect the 5K connector from the control unit. 2. Inspect the connectors and contacts of the sockets to make sure they are in good contact. If the pins are bent, loose or corroded, repair them and check the...
Checking the switch 1. Remove the switch. 2. Check the continuity between the contacts in each switch position, in accordance with the table. Mirror switch: Folder switch:
Checking the controlled mirror 1. Pull out the facing panel. 2. Disconnect the 8K connector from the mirror motor 3. Check the operation of the drive by connecting power and ground according to the table. Mirror drive: Spreader drive:
Replacing the mirror drive (Types: Honda Lock and Murakumi) 1. Remove the controlled mirror from the door and disconnect the 8K connector. 2. Remove the mirror base cover from the mirror base. 3. Remove the two screws and cut the wires, then...
Wipers/window washers Checking the wiper/washer switch Windshield washer/wiper/rear window switch: 1. Remove the driver's side lower dashboard cover. 2. Remove the steering column covers. 3. Disconnect the 8K and 6K connectors from the...
Checking the input signal of the headlight washer control unit 1. Remove the driver's side trim panel, then disconnect the 6K connector from the control unit. 2. Inspect the connectors and contacts of the sockets to make sure they are in reliable contact. If the pins are bent,...
Checking the steerable antenna motor 1. Remove the trunk corner trim panel (combi). 2. Disconnect the gearbox connector from the engine and remove the connector from its clamp. 3. Check the presence of power to the motor in the connector contacts: The...
Sound signals Checking the switch (with SRS) 1. Disconnect the negative battery cable, then disconnect the positive cable and wait at least three minutes. 2. Disconnect the connector (s) driver airbags (and passenger). 3. Remove the...
Integrated control unit Checking the input signal (model KS) This area contains the SRS parts. Before you begin repairs and maintenance, review the SRS parts locations, safety precautions, and work procedures in the SRS section. 1. Remove the...
Power windows — checking the main switch Checking the main switch (body type "hatchback") 1. Remove the driver's door trim. 2.. Disconnect the 12-pin connector from the main switch. 3. Check for continuity between the terminals in accordance with the table....
Window lifters — check Checking the main switch input signal (combi). Note: The control unit is built into the main power window switch and only controls the driver's door window. 1. Remove the main power window switch and armrest pocket from...
Controlled door locks Checking the input signal of the lock control unit 1. Remove the driver's side door panel. 2. Disconnect the 8K connector from the control unit. 3. Inspect the connectors and contacts of the sockets to make sure they...
Immobilizer (engine blocking system) Description The vehicle is equipped with an engine immobilizer system that prevents the vehicle from operating until the correct key is used. This system consists of a pulse transceiver located in the ignition key, a...