Repair of the engine located in the car Honda Civic 6

Engine specifications
Repair without removing from the car General parameters Characteristic Meaning Firing order 1–3–4–2 Cylinder numbering (front to back) 1–2–3–4 Cylinder diameter, mm 74.93 Piston stroke, mm 89.92 Working volume, cm³ (l)...

Engine Repair Without Removing It From the Vehicle — General Information
This Part of the Engine Chapter is devoted to the non-in situ repair of the 1.6L 4-cylinder petrol engine equipped with a fuel injection system. All procedures requiring removal of the power unit are given in Part...

Preparatory actions and list of repair procedures
Clean the engine compartment and the outside surfaces of the power unit using one of a wide range of special solvents. This treatment will prevent dirt from getting inside the engine. If necessary, depending on the...

Bringing the piston of the first cylinder to the top dead center (TDC) position
Note: The following procedure is based on the assumption that the spark plug wires and distributor are installed correctly. If it is necessary to bring the engine to TDC to adjust the distributor position, the piston...

Removal and installation the cylinder head cover
Removal 1. Disconnect the negative cable from the battery. Warning! If the car stereo system is equipped with a security code, make sure you have the correct combination to activate the audio system before disconnecting...

Removal and installation the intake manifold
Warning! Remember that gasoline is a highly flammable liquid – when working with fuel system components, observe all accepted fire safety measures. Do not smoke or approach the work area with an open flame or...

Removal and installation the exhaust manifold
Removal 1. Disconnect the negative cable from the battery. Warning! If the car stereo system is equipped with a security code, make sure you have the correct combination to activate the audio system before disconnecting...

VTEC Systems — General Information and Component Health Checks
General information Some Honda models are equipped with Variable Valve Timing Electronic Control (VTEC). Civic models can use one of two different types of VTEC (VTEC and VTEC-E). The difference between conventional...

Removal, condition check and installation of rocker arm assembly
Note: The camshaft bearing caps are removed together with the rocker arm assembly. To prevent the camshaft from jumping out under the effect of the timing belt tension, ask an assistant to hold the shaft and immediately...

Replacing valve springs with plates and oil deflector caps
Note: Broken valve springs and worn valve stem seals can be replaced without removing the cylinder head. All you need is two special tools and a source of compressed air. 1. Remove the cylinder head cover (see Removal...

Removal, condition check and installation of the timing belt and timing drive gears
Removal 1. Disconnect the negative cable from the battery. Warning! If the car stereo system is equipped with a security code, make sure you have the correct combination to activate the audio system before disconnecting...

Replacing the front crankshaft oil seal
1. Remove the drive belts (see Chapter Routine maintenance ). 2. Remove the crankshaft pulley. 3. Remove the timing belt (see Removal, condition check and installation of the timing belt and timing drive gears ). 4a....

Removal, condition check and installation of the camshaft
Checking axial play and lateral runout 1. Checking the axial clearance is performed as follows: a) Install the camshaft into the engine and secure it with the bearing caps; b) Secure the dial gauge to the cylinder head,...

Removal and installation the cylinder head
Caution! Wait until the engine has cooled down completely before starting work. Removal 1. Bring the piston of the first cylinder to the TDC position at the end of the compression stroke (see Bringing the piston of the...

Removal and installation the engine oil pan
Removal 1. Warm up the engine to normal operating temperature, then drain the engine oil and remove the oil filter (see Chapter Routine maintenance ). 2. Disconnect the negative cable from the battery. Warning! If the...

Removal, inspection and installation of the oil pump
Removal 1. Remove the timing belt (see Removal, condition check and installation of the timing belt and timing drive gears ). 2. Remove the engine oil pan (see Removal and installation the engine oil pan ). 3....

Removal and installation the flywheel/drive disc
Removal 1. Jack up the vehicle and place it on supports. Remove the gearbox (see Chapter Gearshift box ). 2. On models with manual transmission, remove the clutch assembly (see Chapter Clutch and drive shafts )....

Replacing the rear crankshaft oil seal
1. Remove the gearbox (see Chapter Gearshift box ). 2. Remove the flywheel/drive plate (see Removal and installation the flywheel/drive disc ). 3. Before removing the old oil seal, be sure to measure the gap between its...

Checking the condition and replacing the powertrain suspension supports
Powertrain suspension mounts rarely require attention, but damaged mounts should be replaced without delay to avoid increased stress and premature wear of transmission line components. Examination 1. To check, it is...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Link in different formats to this section

TEXTHTMLBB Code

Civic 8 (2005-2011)

Civic 7 (2000-2005)