Front and rear suspension of the car Honda Civic 7

Suspension — Preliminary Checks
1. Check the tire type and tire pressure. If the pressure is not correct, adjust the pressure. Tyre type - 185/70 R14, 185/65 R15,195/60 R15 Tire pressure: sedan, 5-door hatchback - 210 kPa 3-door hatchback: front...

Checking and adjusting the front wheel alignment angles
The values of the wheel alignment angles are given in the table "Wheel alignment angles". Checking the wheel turning angles Place the vehicle on a wheel alignment stand and check the maximum wheel turning angles. Note:...

Checking the rear wheel alignment angles
The values of the wheel alignment angles are given in the table "Wheel alignment angles". Checking wheel alignment 1. Place the vehicle on the stand. 2. Unscrew the wheel hub mounting nut. 3. Install the special device....

Front wheel steering knuckle and hub
Checking the axial clearance in the hub bearing 1. Jack up the front of the car and place it on stands. Table. Wheel alignment angles. Installation angles Size Front wheels Convergence 0±3 mm Wheel turning angles Inner...

Front suspension strut
Removal 1. Jack up the front of the car. 2. Remove the front wheels. 3. Remove the cotter pin and unscrew the nut securing the tie rod end. Using a special tool, disconnect the tie rod end from the steering knuckle. 4....

Lower control arm of the front suspension
Removal and installation 1. Jack up the front of the car and place it on stands. 2. Loosen the wheel mounting nuts and remove the wheel. 3. Hold the ball joint pin (C) with the Allen key (D), and loosen the stabilizer...

Front suspension anti-roll bar
Removal and installation 1. Jack up the car and place it on stands. 2. Remove the front wheels. 3. Hold the ball joint pin (B) with the Allen key (C) and loosen the stabilizer bar strut mounting nut. Disconnect the...

Rear Wheel Hub (2WD models with rear drum brakes)
Checking the axial clearance in the hub bearing 1. Jack up the front of the car and place it on stands. 2. To hold the brake drum, tighten the nuts to the specified torque. Tightening torque - 108 Nm 3. Install the dial...

Rear Wheel Hub (2WD models with rear disc brakes)
Checking the axial clearance in the hub bearing 1. Jack up the front of the car and place it on stands. 2. To hold the brake disc, tighten the nuts to the specified torque. Tightening torque - 108 Nm 3. Install the dial...

Rear Wheel Hub (4WD Models)
Removal and installation 1. Jack up the rear of the vehicle and place it on stands. 2. Loosen the nuts and remove the wheel. 3. Unlock the rim (B) of the nut (A) and unscrew the nut. Tightening torque - 185 Nm 4. Remove...

Rear suspension strut
Removal 1. Jack up the rear of the vehicle and place it on stands. 2. Remove the rear wheels. 3. Loosen the bolt and disconnect the rear suspension strut (A) from the trailing arm (B). 4. Unscrew the nuts securing the...

Rear suspension anti-roll bar
Removal and installation 1. Jack up the rear of the vehicle and place it on stands. 2. Remove the rear wheels. 3. Hold the ball joint pin with a hex key and loosen the stabilizer bar mount nut. Disconnect the strut from...

Upper wishbone
Removal and installation 1. Jack up the rear of the vehicle and place it on stands. 2. Remove the rear wheels. 3. Disconnect the wheel speed sensor wire from the upper control arm. 4. Loosen the bolts and remove the...

Trailing arm
Removal and installation 1. Remove the hub and axle (2WD models) or bearing holder (4WD models). 2. Jack up the trailing arm (A) of the rear suspension. 3. While holding the stabilizer link pin with a hex key (D),...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Link in different formats to this section

TEXTHTMLBB Code

Civic 8 (2005-2011)

Civic 7 (2000-2005)