Exterior (external body elements) of car Honda Civic 8

Replacing the front belt
Note: When installing and removing the front bumper, be careful not to scratch the front bumper itself and the car body. Wear protective gloves. 1. Remove screws A and fasteners B, then remove the front belt C. 2....

Removal and installation the front bumper
Removal and installation of the front bumper is carried out by two people with an assistant. When removing components, use an upholstery tool kit or similar. When installing/removing the front bumper, be careful not to...

Removal and installation the rear bumper
Removal and installation of the front bumper is carried out by two people with an assistant. When removing components, use an upholstery tool kit or similar. When installing/removing the front bumper, be careful not to...

Removal and installation the rear bumper damper
Note: Be careful not to scratch the front bumper and surrounding parts. Wear protective gloves. 1. Remove the rear bumper. 2. Remove bolts A and clips B, then separate rear bumper C from damper D. 3. Install the...

Replacing the rear bumper reflector
Note: When removing/installing the rear bumper, be careful not to scratch the bumper itself and the car body. Wear gloves to avoid damage. 1. Remove the rear bumper. 2. Press the latch A, unhook the hook B, then remove...

Replacing the front bumper shield
Note: Do not damage the front bumper. 1. Remove the front bumper. 2. Press the inner hook A and install the bumper shield B onto the outer hook C, then remove it. 3. Install the shield on the bumper. Securely hook the...

Replacing the front mudguard
Note: Do not scratch the body. 1. Remove the front belt. 2. Remove the front wheel arch protector. 3. Remove the front plastic mudguards A. Remove the retainer B securing the engine cover C and the front mudguard liner....

Replacing the front wheel arch protector
Note: Use an upholstery tool kit or similar when removing components. Avoid scratching the body. Wear protective gloves. 1. Remove the front belt. 2. Remove the screws (A, B) and clip C holding the front wheel arch...

Adjusting the hood
1. Remove the following parts: front fender trim; front emblem cover; shield covers. 2. Slightly loosen each bolt A. 3. Adjust the position of the hood in sequence. Adjust the right and left parts of the hood, as well...

Replacing the hood insulator (for some models)
1. Using a clip remover, disconnect the clips. Remove hooks A, then remove hood insulator B. 2. Perform the insulator installation operations in the reverse order of removal, observing the following: Check the clamps...

Replacing the hood lock
1. Remove the front emblem cover. 2. Disconnect the hood lock switch connector A, then release the connector lock B. 3. Remove the bolts, then remove the hood lock C from the body. 4. Disconnect the hood release cable D...

Replacing the hood release lever
1. Remove the knockout panel. 2. Loosen the bolt and remove the fastener A, then remove the hood release lever B from the body. 3. Disconnect the hood release cable C from the hood release lever. Be careful not to twist...

Replacing the hood seal
1. Using a clip remover, release the clips, then remove the hood seal A. Be careful not to damage the paint finish of the hood. 2. Install the seal in the reverse order of removal, check the clips for damage or...

Removal the front side pillar trim
Note: Use an upholstery tool kit or similar when removing components. 1. Open the front door. 2. Carefully insert the special tool near the upper retainer and press it against the corner trim of the front A-pillar. Be...

Windshield Shield Replacement
Note: Do not scratch the body. 1. Activate the windshield wiper switch and rotate the windshield wiper blades 90°. 2. Remove the central shield A. Remove the rear hood seal B by pulling it outward. Remove the C...

Front Fender Trim Replacement
Note: Avoid scratching the fender trim and body. When removing components, use an upholstery tool kit or similar. 1. Remove the front emblem cover. 2. On the right side, disconnect the washer pipe A and remove the...

Replacing the rear wheel arch protector
Note: Use an upholstery tool kit or similar when removing components. Avoid scratching the body. Wear gloves to protect your hands. 1. Loosen screws A and clamp B securing the rear wheel arch protector C. 2. Carefully...

Roof Molding Replacement
Note: Wear protective gloves. Do not damage the windshield. Do not use metal tools to remove the roof molding, otherwise you may chip the edges of the windshield and cause cracks in the windshield. When removing...

Replacing the side sill panel
Note: Do not scratch the body. 1. Remove the following parts: front wheel arch protector as required; rear wheel arch protector as required. 2. Remove the side sill panel A. Remove screw B and fasteners C. Move the side...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Link in different formats to this section

TEXTHTMLBB Code

Civic 8 (2005-2011)

Civic 7 (2000-2005)