Repair of the engine in car Honda Integra

Engine specifications
Repair without removing from the car General parameters Characteristic Meaning Firing order 1–3–4–2 Cylinder numbering (from left to right) 1–2–3–4 Cylinder diameter, mm 81.03 Piston stroke, mm B18B1 88.90 B18C1 and...

Engine Repair Without Removing It From the Vehicle — General Information
This Part of the Chapter Engine this article is dedicated to the repair of a 1.8 L 4-cylinder petrol engine equipped with a fuel injection system, which is not related to the removal from the car (in situ). All...

Preparatory actions and list of repair procedures
Clean the engine compartment and the outside surfaces of the power unit using one of a wide range of special solvents. This treatment will prevent dirt from getting inside the engine. If necessary, depending on the...

Bringing the piston of the first cylinder to the top dead center (TDC) position
Note: The following procedure is based on the assumption that the spark plug wires and distributor are installed correctly. If it is necessary to bring the engine to TDC to adjust the distributor position, the piston...

Removal and installation the cylinder head cover
Removal 1. Disconnect the negative cable from the battery. Warning! If the car stereo system is equipped with a security code, make sure you have the correct combination to activate the audio system before disconnecting...

Removal and installation the intake manifold
Warning! Remember that gasoline is a highly flammable liquid – when working with fuel system components, observe all accepted fire safety measures. Do not smoke or approach the work area with an open flame or...

Removal and installation the exhaust manifold
Removal 1. Disconnect the negative cable from the battery. Warning! If the car stereo system is equipped with a security code, make sure you have the correct combination to activate the audio system before disconnecting...

Removal, checking and installation the timing belt and timing drive gears
Removal 1. Disconnect the negative cable from the battery. Warning! If the car stereo system is equipped with a security code, make sure you have the correct combination to activate the audio system before disconnecting...

Replacing the front crankshaft oil seal
1. Remove the drive belts (see Chapter Routine maintenance ). 2. Remove the crankshaft pulley. 3. Remove the timing belt (see Audio system ). 4a. Remove the outer crankshaft belt guide. 4b. Remove the crankshaft timing...

VTEC Systems — General Information and Component Health Checks
General information Many Honda models are equipped with Variable Valve Timing Electronic Control (VTEC). The difference between conventional engines and engines equipped with the VTEC system is in the configuration and...

Removal, inspection and installation of camshafts and rocker arm assemblies
1. Checking the axial clearance is performed as follows: a) Install the camshaft into the engine and secure it with the bearing caps; b) Secure the dial gauge to the cylinder head, resting its plunger against the end of...

Replacing valve springs with plates and oil deflector caps
Replacing broken valve springs and defective valve stem seals on VTEC models requires first removing the cylinder head. Remove the camshafts and cylinder head, then refer to Parts General and major engine repairs of...

Removal and installation the cylinder head — removing, checking and installing
Caution! Wait until the engine has cooled down completely before starting work. Components of the engine compartment of the vehicle that must be removed when removing the cylinder head 1 - Air intake duct; 2 - Steering...

Removal and installation the engine oil pan
Removal 1. Warm up the engine to normal operating temperature, then drain the engine oil and remove the oil filter (see Chapter Routine maintenance ). 2. Disconnect the negative cable from the battery. Warning! If the...

Removal, inspection and installation of the oil pump
Removal 1. Remove the timing belt (see Removal, condition check and installation of the timing belt and timing drive gears ). 2. Remove the engine oil pan (see Removal and installation the engine oil pan ). 3....

Checking the condition and replacing the powertrain suspension supports
Powertrain suspension mounts rarely require attention, but damaged mounts should be replaced without delay to avoid increased stress and premature wear of transmission line components. Examination 1. To check, it is...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Link in different formats to this section

TEXTHTMLBB Code

Civic 8 (2005-2011)

Civic 7 (2000-2005)