Electrical equipment of the car engine Honda Civic 6

Engine Electrical Equipment — General Information and Precautions
The engine electrical equipment includes components of the ignition, charging and starting systems (see illustrations below). Since these systems are directly related to engine operation, they are considered separately...

Engine electrical components layout diagram
Schematic diagram of the location of the engine electrical components in the engine compartment of the car (Civic) 1 - Power Control Module (PCM) (inside the car); 2 - High Voltage spark plug wires; 3 - TDC/CKP/CYP...

Engine Electrical Specifications
Ignition system Ignition coil Characteristic Meaning Civic (hitachi distributor) Primary winding resistance, Ohm 0.45÷0.55 Secondary winding resistance, kOhm 22.4÷33.6 Civic (tES distributor) Primary winding resistance,...

Checking the battery status and replacing it
Examination 1. Disconnect both wires from the battery. Caution! The negative cable should always be disconnected first and reconnected last. If the car stereo system is equipped with a security code, make sure you have...

Checking the condition and replacing battery wires
1. Regularly inspect the battery cables along their entire length for damage, cracks, burnt-out insulation, and traces of corrosion. Remember that poor electrical connection of the contact terminals can lead to...

Ignition system — general information
Attention! The transistor electronic ignition system used in the models of cars under consideration generates a higher voltage than that typical for conventional ignition systems. Be careful and observe all necessary...

Checking the functioning of the ignition system
Caution! Due to the very high voltage generated in the ignition system, its components must be serviced with extreme caution. This applies not only to the main components of the electronic ignition system, but also to...

Checking the condition and replacing the ignition coil
Examination 1. Turn off the ignition (the key must be turned to the OFF position). 2. Remove the distributor cap, runner and protective screen (with appropriate equipment). 3. Disconnect the electrical connectors of the...

Checking and replacing the ignition control module (ICM)
Examination 1. Check for proper power supply to the ignition module. Remove the distributor cap and rotor and disconnect the black/yellow wire from the ICM (see accompanying illustration). Check for battery voltage...

Removal and installation the ignition distributor
Removal 1. Disconnect the negative cable from the battery. Warning! If the car stereo system is equipped with a security code, make sure you have the correct combination to activate the audio system before disconnecting...

Checking the installation and adjusting the ignition timing angle
Note: The procedure described below applies to most vehicle models covered in this manual. However, if the VECI label data differs from the following, follow the VECI instructions. 1. Start the engine and warm it up to...

Charging system — general information and precautions
General information The components of the charging system include the alternator, its built-in voltage regulator, charge level indicator, battery, protective fuse and the wiring that connects these components. The...

Checking the status of the charging system
1. Remember that charging system malfunctions are not necessarily related to generator failures. Always perform the following simple checks first: a) Check the condition of the battery wires where they are connected to...

Removal and installation the generator
1. Disconnect the negative cable from the battery. Warning! If the car stereo system is equipped with a security code, make sure you have the correct combination to activate the audio system before disconnecting the...

Replacing the voltage regulator and generator brushes
Note: All Civic models and some 1998 Integra models use Mitsubishi alternators. Replacing the brushes and voltage regulator here requires complete disassembly of the alternator and should be left to a professional....

Starting System — General Information and Precautions
General information The system ensures that the engine is turned over in order to start it. The main components of the system are the starter with a traction relay installed on it, the battery, the ignition switch and...

Checking the proper functioning of the starter on the vehicle (in situ)
Note: Before performing any starter function tests, make sure that the hard starting condition is not caused by a low battery level. 1. If the starter does not turn at all when the ignition key is turned to the START...

Removal and installation the starter
1. Disconnect the negative cable from the battery. Warning! If the car stereo system is equipped with a security code, make sure you have the correct combination to activate the audio system before disconnecting the...

Removal and installation the traction relay
Attention! The Integra models use a Nippondenso starter with a non-removable traction relay. In case of failure, the entire assembly is subject to replacement. The description below applies to Mitsubishi starters. 1....

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Link in different formats to this section

TEXTHTMLBB Code

Civic 8 (2005-2011)

Civic 7 (2000-2005)