Cooling and lubrication of R18A engine of car Honda Civic 8
Replacing the coolant
1. Start the engine. Set the heating system temperature control to the maximum air temperature, then turn off the ignition. Make sure the engine and radiator are cool to the touch. 2. Remove the radiator cap. 3. Remove...
1. Start the engine. Set the heating system temperature control to the maximum air temperature, then turn off the ignition. Make sure the engine and radiator are cool to the touch. 2. Remove the radiator cap. 3. Remove...
Checking the coolant
1. Check the coolant level in the expansion tank. Make sure it is between the "MAX" A and "MIN" B marks. 2. If the coolant level in the expansion tank is at or below the "MIN" mark, add coolant to a level between the...
1. Check the coolant level in the expansion tank. Make sure it is between the "MAX" A and "MIN" B marks. 2. If the coolant level in the expansion tank is at or below the "MIN" mark, add coolant to a level between the...
Disabling/installing the air purifier
1. Disconnect the MAF sensor/IAT sensor A connector. 2. Remove the air cleaner housing cover B. 3. Remove air cleaner element C from air cleaner housing D. 4. Loosen bolt E and pipe F. 5. Remove the air cleaner housing....
1. Disconnect the MAF sensor/IAT sensor A connector. 2. Remove the air cleaner housing cover B. 3. Remove air cleaner element C from air cleaner housing D. 4. Loosen bolt E and pipe F. 5. Remove the air cleaner housing....
Removal and installation the thermostat housing
Removal 1. Drain the engine coolant. 2. Remove the air cleaner housing assembly. 3. Remove the harness clamp A, and cover the air/fuel ratio (A/F) sensor connector and the secondary heated oxygen sensor connector...
Removal 1. Drain the engine coolant. 2. Remove the air cleaner housing assembly. 3. Remove the harness clamp A, and cover the air/fuel ratio (A/F) sensor connector and the secondary heated oxygen sensor connector...
Checking the Thermostat
Replace the thermostat if it is open at room temperature. To check for a closed thermostat: 1. Hang thermostat A in a container of water. Do not allow thermometer B to touch the bottom of the container. 2. Heat the...
Replace the thermostat if it is open at room temperature. To check for a closed thermostat: 1. Hang thermostat A in a container of water. Do not allow thermometer B to touch the bottom of the container. 2. Heat the...
Replacing the thermostat
1. Drain the engine coolant. 2. Remove the wiring harness retaining bracket, then remove the thermostat. 3. Install the thermostat with a new rubber seal. 4. Fill the radiator with coolant, then bleed the air from the...
1. Drain the engine coolant. 2. Remove the wiring harness retaining bracket, then remove the thermostat. 3. Install the thermostat with a new rubber seal. 4. Fill the radiator with coolant, then bleed the air from the...
Replacing the radiator and fan
1. Disconnect the negative cable from the battery, then disconnect the power cable. 2. Remove the battery. 3. Drain the engine coolant. 4. Remove the front grille. 5. Remove the front grille. 6. Disconnect the fan motor...
1. Disconnect the negative cable from the battery, then disconnect the power cable. 2. Remove the battery. 3. Drain the engine coolant. 4. Remove the front grille. 5. Remove the front grille. 6. Disconnect the fan motor...
Replacing the Coolant Temperature (ECT) Sensor 1
1. Drain the engine coolant. 2. Disconnect the ECT sensor 1 connector. 3. Remove the ECT 1V sensor. 4. Install the sensor in the reverse order of removal, with a new sealing ring C, then fill the radiator with coolant.
1. Drain the engine coolant. 2. Disconnect the ECT sensor 1 connector. 3. Remove the ECT 1V sensor. 4. Install the sensor in the reverse order of removal, with a new sealing ring C, then fill the radiator with coolant.
Removal and installation the engine oil level sensor
1. Remove the lower engine cover. 2. Drain the engine oil. 3. Unscrew bolts A, remove cover B and connector C of the engine oil level sensor. Note: If the cover is damaged, replace it. 4. Remove bolts A, then remove...
1. Remove the lower engine cover. 2. Drain the engine oil. 3. Unscrew bolts A, remove cover B and connector C of the engine oil level sensor. Note: If the cover is damaged, replace it. 4. Remove bolts A, then remove...
Checking the engine oil level sensor
Note: This procedure checks the engine oil level sensor for proper operation. Perform the procedure on a flat surface. Make sure the customer has not added oil before performing this procedure. Check for oil leaks...
Note: This procedure checks the engine oil level sensor for proper operation. Perform the procedure on a flat surface. Make sure the customer has not added oil before performing this procedure. Check for oil leaks...
Replacing the engine oil filter supply pipe
1. Remove the filter. 2. Remove the oil pan. 3. Remove the oil filter inlet pipe. 4. Install two 20x1.5mm A nuts onto the new oil filter feed pipe. Hold the nut with a flat wrench, then tighten the second nut with...
1. Remove the filter. 2. Remove the oil pan. 3. Remove the oil filter inlet pipe. 4. Install two 20x1.5mm A nuts onto the new oil filter feed pipe. Hold the nut with a flat wrench, then tighten the second nut with...
Checking the engine oil pipe bolts
1. Remove the piston oil cooling nozzle. 2. Check the piston oil cooling nozzle as follows. Make sure the 1.1mm drill bit fits through the oil jet hole (diameter 1.2 mm). Make sure that the check valve ball A moves...
1. Remove the piston oil cooling nozzle. 2. Check the piston oil cooling nozzle as follows. Make sure the 1.1mm drill bit fits through the oil jet hole (diameter 1.2 mm). Make sure that the check valve ball A moves...
Checking the engine oil pressure sensor
1. Disconnect the engine oil pressure sensor connector A from sensor B. 2. Check for continuity between the positive terminal C and the engine (ground). There should be continuity here with the engine stopped. There...
1. Disconnect the engine oil pressure sensor connector A from sensor B. 2. Check for continuity between the positive terminal C and the engine (ground). There should be continuity here with the engine stopped. There...
Replacing the engine oil pressure sensor
1. Disconnect the oil pressure sensor connector, then remove the sensor itself. 2. Remove all old liquid gaskets from the sensor and its mounting hole. 3. Apply a very small amount of liquid gasket to the threads of the...
1. Disconnect the oil pressure sensor connector, then remove the sensor itself. 2. Remove all old liquid gaskets from the sensor and its mounting hole. 3. Apply a very small amount of liquid gasket to the threads of the...
Disassembling the oil pump
Removal 1. Remove the front wheels. 2. Remove the lower engine cover. 3. Remove the automatic drive belt tensioner. 4. Remove the cylinder head cover. 5. Remove the positive crankcase ventilation (PCV) hose. 6. Remove...
Removal 1. Remove the front wheels. 2. Remove the lower engine cover. 3. Remove the automatic drive belt tensioner. 4. Remove the cylinder head cover. 5. Remove the positive crankcase ventilation (PCV) hose. 6. Remove...
This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Link in different formats to this section
TEXTHTMLBB Code
- General information
- Technical data
- Governing bodies
- Driving and maintenance
- Power unit
- Gasoline engines (L13A)
- Gasoline engines (R18A)
- Diesel engines (N22A)
- Cooling and lubrication (L13A)
- Cooling and lubrication (R18A)
- Cooling and lubrication (N22A)
- Injection system (gasoline)
- Injection system (diesel)
- Toxicity reduction system
- Troubleshooting
- Transmission
- Clutch and drive shafts
- Mechanical gearbox
- Chassis and running gear
- Suspension and wheels
- Steering
- Brake system
- Body and interior
- Exterior (external elements)
- Doors, locks and windows
- Electrical equipment
- Equipment and devices
- Headlights and lighting
- Power devices
- Electrical circuits
- General information
- User manual
- Maintenance
- Power unit
- Engines D15B and D17A
- K20A Engines
- Overhaul engine
- Cooling system
- Lubrication system
- Fuel injection system
- Toxicity reduction system
- Engine electrical equipment
- Transmission
- Clutch
- Manual gearbox
- Automatic gearbox
- Variator (CVT)
- Drive shafts
- Chassis and running gear
- Car suspension
- Steering
- Brake system
- Body and interior
- Exterior (external elements)
- Interior (internal elements)
- Doors, locks and windows
- Heater and air conditioner
- Manual air conditioner
- Automatic air conditioner
- Security system
- Electrical equipment
- Equipment and devices
- Headlights and lighting
- Windscreen wipers
- Audio system
- Electrical diagrams
- General information
- Introduction to guide
- User manual
- Maintenance
- Power unit
- Engine in car (Civic)
- Engine in car (Integra)
- Engine overhaul
- Cooling and heating
- Power and exhaust systems
- Engine electrical equipment
- Engine management systems
- Transmission
- Manual gearbox
- Automatic transmission (AT/CVT)
- Clutch and drive shafts
- Chassis and running gear
- Brake system
- Car suspension
- Steering
- Body and interior
- Exterior (external elements)
- Interior (internal elements)
- Doors, locks and windows
- Electrical equipment
- Equipment and devices
- Electrical circuits
- Power unit
- SOHC engines
- DOHC engines
- Engine overhaul
- Cooling and lubrication system
- Intake and exhaust system
- Fuel injection system (SOHC)
- Fuel injection system (DOHC)
- Carburetor
- Transmission
- Clutch
- Manual gearbox S4C
- Manual gearbox S40
- Automatic gearbox
- Drive shafts
- Chassis and running gear
- Car suspension
- Steering
- Brake system
- Body and interior
- Body elements
- Heater and air conditioner
- Electrical equipment
- Power devices
- Equipment and instruments
- Electrical circuits
- General information
- Maintenance
- Power unit
- Engine in a car
- Engine overhaul
- Cooling system
- Power and exhaust system
- Engine electrical equipment
- Emission control system
- Transmission
- Mechanical gearbox
- Automatic gearbox
- Clutch and drive shafts
- Four-wheel drive
- Chassis and running gear
- Brake system
- Car suspension
- Steering
- Body and interior
- Body elements
- Electrical equipment
- Equipment and devices
- Electrical circuits