Manual car air conditioner Honda Civic 7

Location of air conditioning, heating and ventilation system components
Location of air conditioning, heating and ventilation system components. 1 - pressure switch, 2 - compressor, 3 - receiver, 4 - condenser. Location of air conditioning, heating and ventilation system components. 1 -...

Air conditioning system diagnostics
Reading fault codes 1. Turn the ignition switch to the "OFF" position. 2. Press and hold the air intake actuator switch and the rear window defogger switch, turn the ignition switch to the "ON" position, and release the...

Air flow mixing drive (sedan)
Removal and installation 1. Remove the mounting block in the passenger compartment. 2. Disconnect the connector (A) from the air mixing actuator (B). 3. Loosen the screws and remove the drive. 4. Install in the reverse...

Air flow direction change drive (sedan)
Removal and installation 1. Remove the powertrain control unit. 2. Disconnect the connector (A) from the air flow direction change drive motor (B). Loosen the screws and remove the drive. 3. Install in the reverse order...

Air intake switching drive
Removal and installation Sedan 1. Remove the powertrain control unit. 2. Loosen the bolt and remove the bracket (A). Disconnect the connector (B) and the wiring harness retainer (C). Loosen the screws and remove the air...

Evaporator Air Temperature Sensor (Sedan)
Removal and installation 1. Disconnect the connector (A) from the air temperature sensor behind the evaporator (B), detach the connector retainer (C) from the bracket. Turn the sensor counterclockwise until it stops and...

Thermostat — Removal, Installation and Checking
Removal and installation 1. Disconnect the connector (A) from the thermostat (B), disconnect the connector retainer (C) from the bracket. Loosen the screw and remove the thermostat. 2. Install in the reverse order of...

Power transistor (sedan)
Examination 1. Disconnect the connector from the power transistor. 2. Measure the resistance between terminals "3" and "4". Resistance - 1.5 kOhm ±1% 3. Disconnect contact (A) from terminal "1". Caution: Be careful not...

Air conditioning and heating control panel
Removal and installation Sedan 1. Remove the center panel. 2. Remove the controls (A), unscrew the screws and remove the air conditioning and heating control panel (B) from the center panel (C). 3. Install in the...

Heater Fan Block
Removal and installation Sedan 1. Remove the passenger side lower instrument panel trim, front side trim and glove box. 2. Unscrew the bolt, cut off the plastic spacer as shown in the figure. 3. Remove the relay (A),...

Evaporator — removal and installation
Sedan 1. Remove the refrigerant from the system. 2. Loosen the bolt and disconnect the refrigerant circulation pipes (A) from the evaporator. 3. Remove the heater fan unit. 4. Loosen the bolt and remove the powertrain...

Heater unit — removal and installation
Sedan Attention: components of the passive safety system are located in the area of the heater unit. Before starting work on removing the heater unit, read the safety precautions for operation and repair work (see...

Heater unit — disassembly and assembly
Sedan Disassemble and assemble using the assembly drawing "Disassembling and assembling the heater unit (sedan)". Hatchback Disassemble and assemble using the assembly drawing "Disassembling and assembling the heater...

Heater Unit — Heater Valve Cable Adjustment
Sedan 1. Turn the ignition switch to the "ON" position 2. Set the minimum temperature (18°C). 3. Turn the ignition switch to the "OFF" position. 4. Connect the heater valve cable (B) to the rod (A). Install the cable on...

Heater unit — air flow mixing drive cable adjustment
Hatchback 1. Turn the temperature control to the "MAX COOL" position. 2. Turn the air flow mixing drive rod counterclockwise until it stops and hold it. 3. Connect the cable (B) to the rod (C) and secure with the clamp...

Heater unit — adjusting the air flow direction change drive cable
Hatchback 1. Set the "VENT" mode. 2. Turn the air flow direction change drive rod counterclockwise until it stops and hold it. 3. Connect the cable (B) to the rod (C) and secure with the clamp (A).

Compressor — removal and installation
1. If the compressor is OK, set the idle speed, let the compressor run for a few minutes and turn off the engine. 2. Disconnect the cable from the negative terminal of the battery. 3. Remove the refrigerant from the...

Compressor electromagnetic clutch
Examination 1. Visually assess the condition of the clutch pressure plate. If the pressure plate is damaged, replace the electromagnetic clutch. 2. Rotate the pulley by hand, making sure that it rotates easily and...

Thermal fuse
Removal and installation 1. Loosen the bolt, disconnect the terminal (B) and remove the retainer (C). Disconnect the clutch stator winding connector and remove the thermal fuse (A). 2. When installing a new thermal...

Air conditioner condenser
Removal and installation 1. Remove the refrigerant from the system. 2. Remove the front bumper (see chapter " Body "). 3. Loosen the bolts and disconnect the outlet pipe (A) and inlet pipe (B) from the condenser. Note:...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Link in different formats to this section

TEXTHTMLBB Code

Civic 8 (2005-2011)

Civic 7 (2000-2005)