Exterior (external body elements) of the car Honda Accord 6

General information about the body
The body of the vehicles considered in this Manual has a universal design, the supporting element of which is the floor panel, equipped with front and rear side members and forming a semblance of a frame, to which, in...

Car body and underbody components care
1. It should be remembered that the main factor determining the selling price of a used car is the condition of its body. Body panel maintenance procedures are extremely simple, but must be performed on a regular basis....

Repair of minor damage to body panels
1. If you cannot access the back of the body panel to knock out the dent, you should pull it out using a sliding hammer. In the deepest part of the dent, or along its border, drill or tap small holes at least 2.5 cm...

Repair of seriously damaged body panels
Such repairs are usually performed using welding equipment and must be carried out in a car service workshop. In the event of extensive damage, the first step is to check whether there has been any displacement or...

Maintenance of car hinges and locks
Every 5,000 km (3,000 miles) or every three months, the hinges and assemblies of the door, hood and trunk lid latches should be lubricated with a few drops of liquid oil or a special lock lubricant. The strikers of the...

Replacement of windshield and other fixed glass
Replacing a windshield or other fixed glass on a vehicle requires one of the special quick-setting adhesive or sealant compounds. In addition, this work cannot be done properly without some special tools and experience....

Removal, installation and adjustment of the hood position
Removal and installation Note: The hood panel is quite heavy, so you may want to have an assistant help you. 1. Open the hood, then cover the fenders with special pads or just old blankets to protect them from damage...

Removal and installation the hood lock latch and its drive cable
Warning! The models of vehicles covered in this manual are equipped with a supplemental restraint system (SRS). Before performing any work near the air bag unit, steering column or instrument panel, turn off the SRS to...

Removal and installation front and rear bumper trims
Warning! The models of vehicles covered in this manual are equipped with a supplemental restraint system (SRS). Before performing any work near the air bag unit, steering column or instrument panel, turn off the SRS to...

Removal and installation front fenders
1. Loosen the nuts of the corresponding front wheel. Jack up the front of the car and place it on supports. Remove the wheel. 2. Remove the front bumper cover (see Section Removal and installation front and rear bumper...

Removal, installation and adjusting the trunk lid
Note: The lid is quite heavy, so it might be a good idea to enlist the help of an assistant. Removal and installation 1. Open the trunk lid and secure it in the up position. Cover the painted panels of the trunk edges...

Removal and installation the latch and cylinder of the trunk lid lock
Latch 1. Open the trunk lid and trace the latch assembly with a marker. 2. Disconnect the electrical wiring connector. 3. Remove the two mounting bolts and remove the latch assembly. 4. Disconnect the latch release...

Drive cables for releasing the locks of the luggage compartment lid and the hatch door of the fuel tank filler neck
Trunk lid release cable 1. The procedures for removing the luggage compartment lid latch and disconnecting the drive cable from it are described in Section Removal and installation the latch and cylinder of the trunk...

Removal, installation and adjustment of the door position
Caution: Wear gloves to protect your hands from cuts when performing procedures through access holes in the door frame. Car doors are quite heavy, so it would be wise to enlist the help of an assistant. Removal and...

Removal and installation the latch and outside door handle/lock cylinder
Caution: Wear gloves to protect your hands from cuts when performing procedures through access holes in the door frame. Assembling the lock latch 1. Raise the window glass, then remove the door interior trim panel and...

Removal and installation of door glass
Front door glass 1. Remove the door interior trim panel and moisture protection shield (see Section Removal and installation interior door trim panels ). 2. Lower the window completely. 3. Raise the glass enough to...

Removal and installation rear view mirrors
Exterior mirrors 1. On models equipped with power outside mirrors, remove the interior trim panel and door weather strip (see Section Removal and installation interior door trim panels ). 2. Using a screwdriver, remove...

Removal and installation the front fairing
1. Remove the windshield wiper arms (see Chapter On-board electrical equipment ). 2. Release the three fasteners and remove the fairing panel from the vehicle. The rubber seal may be left attached to the fairing cover....

Geometric dimensions of various body design options
Geometric dimensions of various body design options

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Link in different formats to this section

TEXTHTMLBB Code