Removal and installation of a forward bumper Note: When removing the front bumper, it is good to have an assistant. Do not scratch the grille, front bumper and bodywork. Wear protective gloves. 1. hook; 2. side clamp; 3. upper beam of the front bumper; 4. inner...
Removal and installation of a back bumper Note: When removing the rear bumper, it is good to have an assistant. Do not scratch the rear bumper and bodywork. Wear protective gloves. 1. rear bumper extension; 2. hook; 3. side struts; 4. to the body; 5. back...
Hood — removal and installation 1. Hood; 2. Windshield washer sprayers; 3. Clamps; 4. Clamp; 5. Hook; 6. Windshield washer tube Installation is carried out in the reverse order of removal, taking into account the following: Make sure the hood opens...
Hood adjustment 1. Remove the grille ( see below ). 2. Slightly loosen the hood hinge bolts. 3. Carry out the adjustment of the fit of the hood in the following sequence: Adjust the fit of the hood to the right and left, as well as...
Hood Insulator Replacement Note: Do not scratch the hood. 1. Remove the hood insulator. 1 Disconnect the windshield washer tubes from the nozzles. 2 Release the windshield washer tube from the clips. 3 Using a clip remover, remove the clips,...
Replacing the rubber hood seal 1. Using a clip remover, remove the clips, then remove the hood rubber seal. 2. Installation is carried out in the reverse order of removal. Replace damaged clips.
Removal and installation of a radiator grille Note: Do not scratch the front bumper and adjacent components. 1. Remove the clips and hook from the front bumper, then remove the grille. 1. pin; 2. grille; 3. front bumper; 4. hook; 5. upper beam of the front bumper...
Removal and installation of the platform under the rear license plate Note: Do not scratch the rear bumper and adjacent components. 1. Remove tailgate trim ( see above ). 2. Turn off nuts and a bolt, take out clips, then remove a platform under back license plate. 1. back glass; 2....
Removal and installation of finishing of a bottom of a back door Note: Be careful not to scratch the tailgate or adjacent components. 1. Remove tailgate trim ( see above ). 2. Turn off nuts, take out clips, then remove furnish of a bottom of a back door. 1. Finishing the bottom of...
Dismantling the bottom of the rear door Note: Do not scratch the tailgate bottom trim. 1. Finishing the bottom of the rear door; 2. clamp; 3. lower beam of the rear door Installation is carried out in the reverse order of removal. Replace damaged clips.
Removal and installation of roof spoiler, roof side trim Note: Do not scratch the body and adjacent components. When prying out components with a flat-blade screwdriver, wrap it with protective tape to prevent damage. 1. Remove the plugs from the roof spoiler, then unscrew...
Dismantling the side roof trim Note: Do not scratch the roof side trim. 1. hooks; 2. side roof trim; 3. roof side trim bracket; 4. roof side clamp
Roof molding replacement Note: Don't scratch the body. When prying out components with a flat-blade screwdriver, wrap it with protective tape to prevent damage. Stick the protective tape on the body. 1. windshield molding; 2. roof molding; 3....
Door sill replacement 1. forward; 2. threshold panel; 3. expansion clamp; 4. inner wing 1. Remove the door sill panel. 1. Pull back the inner wing as far as necessary and remove the expansion clips. 2. Slide the threshold panel forward and...
Dismantling the side trim of the bottom Note: Do not scratch the body and adjacent components. 1. Loosen the bolts, remove the clips, then remove the mudguard. 2. Loosen the screws, remove the clips, then remove the inner wing.
Removal and installation of a protective overlay of a fuel tube Note: Do not scratch the body. 1. Remove the clips, then remove the fuel pipe protector. 1. Fuel pipe protector 2. Installation is carried out in the reverse order of removal. Replace damaged clips.
Removing and installing the outlet Note: Do not scratch the body and adjacent components. 1. Remove: rear bumper ( see above ). Rear side trim ( see above ). 2. Installation is carried out in the reverse order of removal.
Replacing the wheel arch trim Note: After bending, the steel core of the wheel arch trim cannot be reshaped. Replace the wheel arch trim after bending the steel core. 1. Remove the wheel arch trim by pulling on it. 2. Clean the contact surface of...
Emblem replacement Glue the emblem in the specified location. Note: Before gluing, clean the surface on the rear door with a sponge soaked in alcohol. After cleaning, do not allow oil, grease and water to come into contact with the...
Subframe replacement Tightening torques for subframe bolts After loosening the subframe fixing bolts, replace them with new ones. 1. CONNECTING BRACKET 2. To the body 3. SPECIAL BOLT, 12x1.5 mm, 54 Nm (5.5 kgf/m) 4. SPECIAL BOLT, 14x1.5 mm,...