Removal and installation of a forward bumper Be careful not to damage the body or the components to be removed. Work with gloves. Do the work with an assistant. Remove the components shown in the figure in numerical order. When installing the bumper, first attach...
Removal and installation of a back bumper Attention. Be careful not to damage the body or the components to be removed. Work with gloves. Do the work with an assistant. While working with a screwdriver, protect the components with protective tape or a cloth....
Hood adjustment 1. Remove the following items. front grille (see below). Front fender trims (see below). 2. Loosen the bolts and then tighten them so that the various components do not move spontaneously. 3. Adjust the position of the...
Removal and installation of an insulator of a cover of a cowl Attention. Do not damage the hood cover and removed components. Remove the clips and remove the hood cover insulator. Remove clips with a clip remover. Install in the reverse order of removal. Check clips for damage and...
Removing and installing hood seals Do not damage the hood cover and removed components. Remove clips and remove hood seals. Install in the reverse order of removal. Check clips for damage and replace if necessary.
Tailgate adjustment 1. Lower the rear end of the ceiling trim (see above). Attention. Do not over-fold the ceiling trim. 2. Loosen the screws and nuts, and then tighten them so that the various components do not move spontaneously. 3....
Removal and installation of racks of a back door Attention. After removing the racks, hold the rear door with your hand while opening and closing it. Be careful not to damage the tailgate or the components to be removed. Do the work with an assistant. If the stand is...
Removal and installation of consolidation of a back door Align the seal center mark shown in the figure; with the center of the opening in the body and install the seal. Before installing the seal, clean the mounting surface of the body with clean gasoline or alcohol, and...
Removal and installation of a dynamic damper Attention. Work with gloves. Be careful not to damage the body or the components to be removed. Remove lower rear door trim (see above). Install in the reverse order of removal.
Fuel filler door — position adjustment 1. Loosen the hinge mounting bolts, and then tighten them until the door spontaneously stops moving. 2. Moving the door in and out, up and down, adjust the gaps and levels. 3. Tighten the door mounting bolts. 4. Check...
Side roof trim 4WD Models Attention. While working with a screwdriver, protect the components with protective tape or a cloth. Also, wrap the screwdriver with tape so as not to damage the components.
Removing and installing roof molding Attention. Do not apply excessive force to the molding. While working with a screwdriver, protect the components with protective tape or a cloth. Also, wrap the screwdriver with tape so as not to damage the components....
Removal and installation of a protective molding Attention. Work with gloves. Do not apply excessive force to the protective molding. If the molding is bent, repair it. Be careful not to damage the doors or the components to be removed. Protect the paintwork from...
Removal and installation of side seal trim Attention. Be careful not to damage the body or the components to be removed. 1. Remove the screws from the underside of the side seal trim and remove the rear seal side trim cover. 2. Loosen the screws on the front...
Removal and installation of finishing of a forward wheel niche 4WD Models Attention. Work with gloves. Do not scratch painted surfaces, protect them with cloth tape. 1. Remove the inner wing (see above). 2. On the inside of the wing, remove the latches, cut off the double-sided...
Removal and installation of finishing of a back wheel niche 4WD Models Attention. Work with gloves. Do not scratch painted surfaces, protect them with cloth tape. 1. Remove the TORX bolt and screws. 2. Cut off the double sided tape and remove the rear wheel well trim. 3. Install...
Removal and installation of a forward lattice Attention. Be careful not to damage the front bumper and removed components. Remove the front bumper and remove the front grille from it. Install in the reverse order of removal. Check the latches for damage and replace...
Removing and installing the rear bottom cover Attention. Be careful not to damage the body or the components to be removed. Remove the rear bumper clips (see above). Install in the reverse order of removal. Check the latches for damage and replace if necessary.
Removal and installation of protection of fuel tubes 2WD Models Attention. Be careful not to damage the body or the components to be removed. Install in the reverse order of removal. Check the latches for damage and replace if necessary.
Removal and installation of a ventilating lattice Attention. Be careful not to damage the body or the components to be removed. Remove rear bumper (see above). Install in the reverse order of removal.
Installation of Emblems/Decals Attach emblems/stickers to the areas shown in the illustration. On non-IHCC models, align the front center emblem with the recess in the front grille, glue and secure with nuts. On models with IHCC, align the front...
Removal and installation of a cable of an opener of a cowl Attention. Do not kink the opener cable. Be careful not to damage the body or the components to be removed. Remove the following components: front grille (see above). Right inner wing (see above). Right front side trim...
Removing and installing fuel filler door opener cable Attention. Do not kink the opener cable. Be careful not to damage the body or the components to be removed. Remove the following components: Right front side trim, (see above). Right lower B-pillar trim (see above)....
Removing and installing the hood opener Attention. Be careful not to damage the body or the components to be removed. Do not kink the opener cable. Remove the right trim of the top cover of the hood (see above). Install in the reverse order of removal....
Removal and installation of the lock of a cowl Attention. Be careful not to damage the body or the components to be removed. Do not kink the opener cable. Remove the front grill (see above). Install in the reverse order of removal. Connect the opener cable securely....
Removal and installation of the fuel filler door opener Attention. Be careful not to damage the body or the components to be removed. Do not kink the opener cable. Install in the reverse order of removal. Connect the opener cable securely. Check if the fuel filler door opens...
Subframe tightening force After installing the subframe, be sure to check the wheel alignment ( see ch. Front and rear suspension ). Front subframe Rear subframe