Car front and rear suspension Honda Avancier 1
Wheel alignment angles — preliminary remarks
Before performing a proper check and adjustment of the wheel alignment, perform the following checks. If the following conditions are not met, proper check and adjustment may not be possible. Make sure that no...
Before performing a proper check and adjustment of the wheel alignment, perform the following checks. If the following conditions are not met, proper check and adjustment may not be possible. Make sure that no...
Wheel alignment — procedure for adjusting wheel alignment angles
All components of the wheel installation are connected to each other. Therefore, when adjusting one of the elements, it is necessary to check the other components and, if necessary, perform a general adjustment. Before...
All components of the wheel installation are connected to each other. Therefore, when adjusting one of the elements, it is necessary to check the other components and, if necessary, perform a general adjustment. Before...
Checking wheels/hubs — bearing axial play
1. Loosen the wheel nuts on the wheel being checked. 2. Using a jack, raise the car so that the wheel is raised off the ground. Caution: Be sure to support the opposite wheel with chocks and lock the rear wheels with...
1. Loosen the wheel nuts on the wheel being checked. 2. Using a jack, raise the car so that the wheel is raised off the ground. Caution: Be sure to support the opposite wheel with chocks and lock the rear wheels with...
Checking wheels/hubs — wheel runout
1. Loosen the wheel nuts on the wheel being checked. 2. Using a jack, raise the car so that the wheel is raised off the ground. Caution: Be sure to support the opposite wheel with chocks and lock the rear wheels with...
1. Loosen the wheel nuts on the wheel being checked. 2. Using a jack, raise the car so that the wheel is raised off the ground. Caution: Be sure to support the opposite wheel with chocks and lock the rear wheels with...
Checking Wheels/Hubs — Removing Ball Joints
Special tool: ball joint puller 07MAC-SL00200. Caution: When removing ball joints, install the special tool accurately. If the special tool is installed incorrectly, the ball joint pin or boot may be damaged. Also, the...
Special tool: ball joint puller 07MAC-SL00200. Caution: When removing ball joints, install the special tool accurately. If the special tool is installed incorrectly, the ball joint pin or boot may be damaged. Also, the...
Front suspension — device
Examination Attention. Before assembly, clean the contact surfaces of the wheel and brake disc, as well as the contact surfaces of the brake disc and hub. Remove the center caps from the inside of the wheel after...
Examination Attention. Before assembly, clean the contact surfaces of the wheel and brake disc, as well as the contact surfaces of the brake disc and hub. Remove the center caps from the inside of the wheel after...
Front Suspension Steering Knuckle and Hub — Removal and Installation
1. Loosen the wheel nuts of the front wheels. 2. Using a jack, lift the car so that the wheels are raised. 3. Remove the front wheels. 4. Loosen the brake hose bracket mounting bolts. 5. Unscrew the two brake caliper...
1. Loosen the wheel nuts of the front wheels. 2. Using a jack, lift the car so that the wheels are raised. 3. Remove the front wheels. 4. Loosen the brake hose bracket mounting bolts. 5. Unscrew the two brake caliper...
Front Suspension Steering Knuckle and Hub — Wheel Bearing Replacement
1. Remove the steering knuckle (see above). 2. Remove the front wheel hub. 3. Remove the locking wheel and mudguard. 4. Remove the wheel bearing from the steering knuckle. 5. Remove the inner ring. Clean the steering...
1. Remove the steering knuckle (see above). 2. Remove the front wheel hub. 3. Remove the locking wheel and mudguard. 4. Remove the wheel bearing from the steering knuckle. 5. Remove the inner ring. Clean the steering...
Replacing the front suspension ball joint boot
1. Remove the clips and remove the cover. Caution: Do not apply lubricant to the boot seating areas. 2. Fill the cover with grease and apply it to the edges. 3. Remove old grease from the tapered area of the ball joint...
1. Remove the clips and remove the cover. Caution: Do not apply lubricant to the boot seating areas. 2. Fill the cover with grease and apply it to the edges. 3. Remove old grease from the tapered area of the ball joint...
Removal and installation the front suspension stabilizer
1. Remove the front wheels (see above). 2. Disconnect the rods from the stabilizer. 3. Remove the stabilizer bushing holders and remove the bushings from the stabilizer. 4. Install in the reverse order of removal....
1. Remove the front wheels (see above). 2. Disconnect the rods from the stabilizer. 3. Remove the stabilizer bushing holders and remove the bushings from the stabilizer. 4. Install in the reverse order of removal....
Front shock absorber
Removal 1. Remove the front wheels (see above). 2. Unscrew the shock absorber bolt. 3. Loosen the self-locking nut (12 mm), remove the fork bolt and remove the shock absorber fork. 4. Unscrew the upper nuts (8 mm) and...
Removal 1. Remove the front wheels (see above). 2. Unscrew the shock absorber bolt. 3. Loosen the self-locking nut (12 mm), remove the fork bolt and remove the shock absorber fork. 4. Unscrew the upper nuts (8 mm) and...
Rear Suspension — Hub & Bearing Assembly (2WD Models)
Component placement/checking Attention: Before assembly, clean the contact surfaces of the wheel and brake disc, as well as the contact surfaces of the brake disc and hub. Remove the center cap of the alloy wheels from...
Component placement/checking Attention: Before assembly, clean the contact surfaces of the wheel and brake disc, as well as the contact surfaces of the brake disc and hub. Remove the center cap of the alloy wheels from...
Rear Suspension Knuckle and Hub (4WD Models) — Inspection, Removal and Installation
Component placement/checking Attention. Before assembly, clean the contact surfaces of the wheel and brake disc, as well as the contact surfaces of the brake disc and hub. Remove the center cap of the alloy wheels from...
Component placement/checking Attention. Before assembly, clean the contact surfaces of the wheel and brake disc, as well as the contact surfaces of the brake disc and hub. Remove the center cap of the alloy wheels from...
Rear Suspension Knuckle and Hub (4WD Models) — Wheel Bearing Replacement
1. Remove the rear wheel hub. 2. Remove the inner ring. 3. Remove the parking brake assembly from the support disc ( see chapter Brake system ). 4. Unscrew the nut (16 mm) and two nuts (10 mm) securing the support disk...
1. Remove the rear wheel hub. 2. Remove the inner ring. 3. Remove the parking brake assembly from the support disc ( see chapter Brake system ). 4. Unscrew the nut (16 mm) and two nuts (10 mm) securing the support disk...
Replacing the rear suspension knuckle bushing (4WD models)
1. Place your fist on the press with the machined surface facing down. 2. Loosen the special tool bolts. 3. Set the outer diameter of the special tool to be equal to the inner diameter of the bushing and tighten the...
1. Place your fist on the press with the machined surface facing down. 2. Loosen the special tool bolts. 3. Set the outer diameter of the special tool to be equal to the inner diameter of the bushing and tighten the...
Replacing the rear suspension ball joint boot (4WD models)
1. Remove the clips and remove the cover. Caution: Do not apply lubricant to the mounting surfaces of the cover. 2. Apply grease to the boot and edge area. 3. Remove old grease from the rubbing areas of the ball joint...
1. Remove the clips and remove the cover. Caution: Do not apply lubricant to the mounting surfaces of the cover. 2. Apply grease to the boot and edge area. 3. Remove old grease from the rubbing areas of the ball joint...
Removal and installation the rear suspension stabilizer
2WD models 1. Remove the rear wheels (see above). 2. Disconnect the stabilizer links from the stabilizer. 3. Remove the bushing holders and stabilizer. 4. Install the stabilizer in the reverse order of removal. During...
2WD models 1. Remove the rear wheels (see above). 2. Disconnect the stabilizer links from the stabilizer. 3. Remove the bushing holders and stabilizer. 4. Install the stabilizer in the reverse order of removal. During...
Rear shock absorbers
Removal 1. Remove the rear wheels (see above). 2. Remove the trim ( see chapter Body ). 3. Unscrew the top nuts. 4. Disconnect the shock absorber from the knuckle and remove it. 2WD models Disconnect the stabilizer link...
Removal 1. Remove the rear wheels (see above). 2. Remove the trim ( see chapter Body ). 3. Unscrew the top nuts. 4. Disconnect the shock absorber from the knuckle and remove it. 2WD models Disconnect the stabilizer link...
This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Link in different formats to this section
TEXTHTMLBB Code
- General information
- Controls and instruments
- User manual
- Power unit
- Engine maintenance
- Engine repair
- Cooling system
- Engine management
- Power and exhaust system
- Transmission
- Automatic gearbox
- Drive shafts and differential
- Chassis and running gear
- Steering
- Car suspension
- Brake system
- Body and interior
- Doors, locks and windows
- Interior (internal elements)
- Exterior (external elements)
- Air conditioner
- Electrical equipment
- Power devices
- Equipment and devices
- Headlights and lighting
- Electrical circuits