Car front and rear suspension Honda Accord 6

Suspension and steering specifications
Suspension type Front 2-lever Back Independent, 5-link Steering type Rack and pinion mechanism with hydraulic booster Hydraulic fluid type PAS See Chapter Settings and ongoing maintenance Wheel alignment angles Wheel...

The structure and description of the suspension and steering
Front Suspension Components 1 - Push bar; 2 - Assembling the shock absorber with a coil spring; 3 - Lower ball joint; 4 - Lower control arm; 5 - Tie rod end; 6 - Stabilizer bar for lateral stability; 7 - Assembly of the...

Removal and installation the front shock absorber assembly with a coil spring
Removal 1. Loosen the nuts of the corresponding wheel. Jack up the front of the car and place it on supports. Remove the wheel. 2. Unbolt the flexible brake hose from the shock absorber assembly. 3. Disconnect the...

Replacing the shock absorber or coil spring of the strut assembly
Typical front shock absorber assembly design with coil spring 1 - Self-locking nut; 2 - Damper rod support washer; 3 - Rubber protective ring of the damper rod; 4 - Damper rod support bushing; 5 - Damper support base; 6...

Removal and installation the steering knuckle
Removal Note: If the wheel cover is not secured with wheel nuts, begin with the procedure in paragraph 4. 1. Loosen the wheel nuts, jack up the front of the car and place it on supports. 2. Loosen the wheel nuts and...

Removal and installation the front hub assembly with wheel bearing
1. Remove the steering knuckle assembly from the vehicle (see Section Removal and installation the steering knuckle ). 2. To squeeze the hub out of the steering knuckle, a special tool is required, and therefore, the...

Removal and installation the front anti-roll bar
1. Set the parking brake. Loosen the front wheel nuts. Jack up the front of the car and place it on supports. Remove the wheels. 2. Disconnect both struts from the anti-roll bar. 3. Unscrew the bolts securing the...

Removal and installation the front suspension push rod
1. Loosen the nuts of the corresponding front wheel. Jack up the front of the car and place it on supports. Remove the wheel. 2. Remove the plug from the plastic splash shield. 3. Loosen the nut securing the front end...

Removal and installation the lower control arm of the front suspension
1. Loosen the nuts of the corresponding front wheel. Jack up the car and place it on supports. Remove the wheel. 2. Remove the through bolt and detach the damper fork from the lower control arm assembly (see Section...

Removal and installation the upper control arm of the front suspension
1. Loosen the nuts of the corresponding front wheel. Jack up the car and place it on supports. Remove the wheel. Support the lower control arm with a jack. 2. Remove the shock absorber assembly with the coil spring (see...

Replacing ball joints
The suspension of each front wheel uses two ball joints. The upper joint is mounted in the upper arm assembly, the lower joint is secured in the steering knuckle. The suspension of the rear wheels uses one ball joint,...

Removal and installation the rear shock absorber assembly with a coil spring
1. Loosen the wheel nuts, jack up the rear of the car and place it on stands. Remove the rear wheels. 2. To provide access to the upper support of the rack. 3. Loosen the upper support mounting nuts. Note: Only the two...

Removal and installation the rear wheel hub assembly
Removal 1. Loosen the nuts of the corresponding rear wheel. Jack up the rear of the car and place it on supports. Remove the wheel. Models with rear disc brakes 2. Unbolt the brake hose mounting bracket from the hub...

Removal and installation the rear hub assembly with wheel bearing
Note: The rear hub is combined with the wheel bearing into a single assembly. The bearing is sealed at the factory and does not require additional lubrication. If the bearing is worn or damaged, it should be replaced...

Removal and installation the rear anti-roll bar
1. Loosen the wheel nuts. Jack up the rear of the car and place it on stands. Remove the rear wheels. 2. Loosen the nuts securing the lower ends of the rod to the struts. 3. Also unscrew the bolts of the clamps securing...

Removal and installation rear suspension arms
Loosen the nuts of the corresponding wheel. Jack up the rear of the car and place it on supports. Remove the wheel. Upper arm 1. Loosen the nut of the upper control arm through bolt to the hub assembly. Also remove the...

Wheels and tires — general information
The wheels of all the models of cars described in this Manual are equipped with radial tires of metric size with fiberglass or steel cord. Installing tires of a different size on the car may affect its handling and ride...

Wheel alignment angles
The front wheel alignment angles determine the geometry of the position of the latter relative to the vehicle suspension and the road surface. Violation of this geometry adjustment leads to decreased vehicle...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Link in different formats to this section

TEXTHTMLBB Code