Car front and rear suspension Honda Fit/Jazz 1

Preliminary checks
Check the tire type and tire pressure. If the pressure is not correct, adjust the pressure. Tyre type 175/65 — R14 82S 185/55 — R1581V Tire pressure - 220 kPa 2. Check the axial clearance of the front wheel hub...

Checking and adjusting the front wheel alignment angles
The values of the wheel alignment angles are given in the table "Wheel alignment angles". Checking the wheel turning angles Place the vehicle on a dynamometer and check the maximum wheel turning angles. Note: If a...

Checking the rear wheel alignment angles
The values of the wheel alignment angles are given in the table "Wheel alignment angles". Checking wheel alignment 1. Place the vehicle on the stand. 2. Unscrew the wheel hub mounting nut. 3. Install the special device....

Checking the wheel runout
1. Jack up the car and place it on stands. 2. Install the dial indicator as shown in the figure and check the axial runout of the wheel. Nominal axial runout - 0-1 mm Maximum axial runout - 2 mm 3. Install the dial...

Front suspension — schematic diagram
Front suspension.

Front wheel steering knuckle and hub
Checking the axial clearance in the hub bearing 1. Jack up the front of the car and place it on stands. 2. Remove the front wheel. 3. To hold the brake disc (drum), tighten the nuts to the specified torque. Tightening...

Front Wheel Steering Knuckle and Hub — Removal
1. Jack up the front of the car and place it on stands. 2. Loosen the wheel mounting nuts and remove the wheel. 3. Loosen the brake pipe bracket mounting bolt. 4. Loosen the bolts and remove the brake caliper assembly....

Front Wheel Steering Knuckle and Hub — Installation
1. Press the new bearing (B) into the steering knuckle (D) using the old bearing (A), steel plate (C) and special tools as shown in the figure. Note: The bearing must be installed with the speed sensor rotor (E) (brown)...

Front suspension anti-roll bar
Replacing the stabilizer bar 1. Jack up the car and place it on stands. 2. Remove the front wheels. 3. Holding the ball joint pin with a hex key, unscrew the stabilizer bar mounting nuts and remove it. A - front...

Front Suspension Strut — Removal
1. Jack up the front of the car. 2. Remove the front wheels. 3. Disconnect the anti-roll bar from the strut. 4. Disconnect the wheel speed sensor retainer from the strut. Do not disconnect the sensor connector. 5....

Front suspension strut — disassembly and assembly
Disassembly and assembly of the front suspension strut. 1 - plug, 2 - nut, 3 - washer, 4 - rack support, 5 - pillow, 6 - bearing, 7 - upper spring seat, 8 - upper spring seat gasket, 9 - compression stroke limiter, 10 -...

Front Suspension Strut — Installation
1. Install the cushion and strut assembly onto the vehicle. 2. Install the strut support, washer and tighten the nut. 3. Install new lower strut mounting bolts, bracket and tighten new nuts. Note: When installing, align...

Lower control arm of the front suspension
Removal and installation 1. Jack up the front of the car and place it on stands. 2. Loosen the wheel mounting nuts and remove the wheel. 3. Remove the front mudguard. 4. Remove the cotter pin and unscrew the nut. Note:...

Checking the axial clearance in the rear wheel hub bearing
1. Jack up the front of the car and place it on stands. 2. Remove the front wheel. 3. To hold the brake disc (drum), tighten the nuts to the specified torque. Tightening torque - 108 Nm 4. Install the dial indicator on...

Rear Wheel Hub (2WD models with rear drum brakes)
Removal and installation the rear wheel hub (2WD models with rear drum brakes). 1 - rear suspension beam, 2 - trunnion, 3 - brake mechanism, 4 - hub, 5 - nut, 6 - cap, 7 - brake drum. Removal and installation 1. Jack up...

Rear Wheel Hub (2WD models with rear disc brakes)
Removal and installation Removal and installation the rear wheel hub (2WD models with rear disc brakes). 1 - rear suspension beam, 2 - trunnion, 3 - mudguard, 4 - hub, 5 - nut, 6 - cap, 7 - brake disc. 1. Jack up the...

Rear Wheel Hub (4WD Models)
Removal and installation 1. Jack up the rear of the car and place it on stands 2. Loosen the nuts and remove the wheel. 3. Remove the cap (A), cotter pin (C) and unscrew the nut (B). 4. Remove washers (D) and (E). Note:...

Bearing replacement
1. Remove the retaining ring (A) from the bearing housing. 2. Using a press and a mandrel, press the bearing pad (B) out of the bearing housing (A). 3. Install the new bearing (B) as shown in the figure, and using the...

Rear suspension beam — removal
1. Remove the hub (2WD models) or bearing housing (4WD models) from the rear suspension beam. 2. Remove the spring. 3. Remove the brake hose retainer (A), disconnect the brake hose (B) from the beam. Note. Do not twist...

Rear suspension spring — removal and installation
1. Remove the rear wheel. 2. Place the rear suspension beam on the jack and raise it until the suspension begins to compress. 3. Remove the bolts securing the rear shock absorbers to the rear suspension beam. A - rear...

Rear shock absorber — removal
1. Remove the rear wheel. 2. Place the rear suspension beam on the jack and raise it until the suspension begins to compress. 3. Disconnect the lower part of the shock absorbers. A - rear suspension beam, B - shock...

Checking the rear shock absorber
1. Check the shock absorber for damage and leaks. 2. Compress and stretch the shock absorber at least three times. Make sure that the resistance to movement does not change and there are no extraneous sounds. Replace...

Installing the rear shock absorber
1. Compress the shock absorber by hand and install it on the car. Be careful not to damage the body. 2. Jack up the rear suspension beam with a jack. 3. While moving the jack, align the hole in the beam and shock...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Link in different formats to this section

TEXTHTMLBB Code