Contents: Front seat adjustment ⇊ Headrests ⇊ Center rear seat headrest ⇊ Armrests ⇊ Rear seats ⇊ Folding the rear seat back ⇊ Raising the rear seat cushion ⇊ Electric heated seats (for some…⇊
Note: Adjust the seat position before driving.
Front seat adjustment
Driver's seat
To adjust the longitudinal position of the seat, lift the locking lever located at the front under the seat cushion. While holding the lever, move the seat forward or backward to a comfortable position. Then release the locking lever. To check that the seat is securely locked, try moving it forward and backward.
To change the angle of the seat back, lift the release lever located on the side of the seat cushion base (from the door side).
To check that the seat back is securely locked, try tilting it forward and backward.
Driver's seat height adjustment
You can adjust the driver's seat height. To increase the seat height, pull the adjustment lever located on the side of the seat cushion base up several times (from the door side). To decrease the seat height, press the adjustment lever several times.
When adjusting, move the lever up or down until it stops.
Headrests
All vehicle seats are equipped with head restraints to help prevent neck and head injuries in the event of a rear-end collision.
In order for the head restraints to effectively perform their protective functions, they must be adjusted correctly. Adjust the height of the head restraints so that the back of your head rests on the middle part of the head restraint.
The height adjustment of the headrest position is carried out with both hands at the same time, so do not try to adjust the headrest while the car is moving. To raise the headrest, simply pull it up. To lower the headrest, you must first press the locking button on the side, shown in the figure. After pressing the button, lower the headrest to the desired position.
Center rear seat headrest
If the center rear seat is occupied by a passenger, set the head restraint of that seat to the highest position.
To remove the headrest for cleaning or replacement, or to fold the rear seat, do the following: Raise the headrest up to the stop. Then press the lock button and remove the headrest from the seat back.
Caution: After lifting the folded rear seat back, be sure to reinstall the head restraint.
Armrests
Front armrest (for some vehicle versions)
You can use the lid of the box in the center console as a front armrest.
Make sure that when you move the cover, you do not pinch your fingers or the passenger's.
Rear armrest (for some vehicle versions)
Lower the rear seat center armrest to the horizontal position if you want to use it.
A cup holder is built into the rear seat centre armrest.
Rear seats
The left and right rear seat backs can be folded to increase luggage compartment volume.
In addition, both rear seat cushions can be raised separately.
With one rear seat folded down, you can only transport one passenger in the rear row. Two people riding on the rear seats is prohibited in this case, since with the rear seat folded down, it is impossible to properly fasten the seat belt for the center seat of the rear row.
Before folding the rear seat back or cushion, remove all objects from it.
Folding the rear seat back
Before folding the rear seat, make sure that there are no objects left on the passenger compartment floor.
1. Install the center armrest in place (in the raised position).
2. Place the seat belt into the bracket on each side.
3. Lower the headrest to its lowest position.
4. Slide the locking lever located on the backrest upwards, closer to the door.
5. Tilt the backrest forward as far as it will go.
Caution: Do not place heavy loads on the back of the folded seat.
To raise the backrest, perform the above steps in reverse order. Check that the backrest is securely locked. If the backrest is not locked in the raised position, the seat belt will not function properly. The locking lever will be in a position where the red mark is visible on it.
Attention! Before starting to move the vehicle, make sure that the seat backs are securely fixed.
If you cannot fold the rear seatback completely because its head restraint hits the front seatback, remove the head restraint.
Caution: After lifting the folded rear seat back, be sure to reinstall the head restraint.
Raising the rear seat cushion
1. Install the center armrest in place (in the raised position).
 |
 |
2. Place the seat belt into the bracket on each side.
3. Turn the seat cushion up and press it against the backrest, then fold the seat support, which should be fixed on the cushion. Check the reliability of the folded cushion.
To return the seat cushion to its working position, pull the support up until it stops. Then press the cushion down, holding it with your hand.
Make sure that the lowered cushion is securely fixed and that the support is in the correct position.
Electric heated seats (for some vehicle versions)
Both front seats of the vehicle can be equipped with electric heaters, which operate only when the ignition is on (ignition key turned to the "ON" (II) position).
Press the front part of the switch button ("HI") to turn on the quick seat heating mode. Once the seat has warmed up to the desired temperature, press the back part of the switch button ("LO") to switch to the constant seat heating mode.
When operating in the high heat mode ("HI"), the system automatically turns off after the seat is heated, and then turns back on when the seat cools down.
When operating in the moderate heating mode ("LO"), the system operates continuously, without turning off or on automatically when the seat temperature changes.
Follow these guidelines when using the seat heating system:
- use the "HI" mode only for quick seat heating, as this mode uses up a lot of battery power;
- do not turn on the seat heating even in the moderate heating mode ("LO") when the engine is not running or when the engine is idling for a long time. This may lead to a severe discharge of the battery and difficulties in starting the engine.
[You will find the original on the portal: HondaBook]