Unfortunately, the results of readings taken with a vacuum meter are easily misinterpreted, and therefore, they must be analyzed together with data obtained during other diagnostic checks.
When reading the vacuum gauge indicator, you should pay attention not only to the absolute value of the arrow's deflection, but also to its speed of movement. Most imported gauges show the vacuum depth in inches of mercury. It should be taken into account that all regulatory requirements are given for the case of testing at zero altitude above sea level. An increase in relief for every 300 m after the 600 m mark leads to an underestimation of the instrument's readings by approximately 25 mm.
Attach the vacuum gauge directly to the intake manifold - not to the throttle body. Make sure that all hoses remain connected during the test - otherwise the reading will not be reliable.
Before taking measurements, warm up the engine to normal operating temperature. Chock the wheels and set the parking brake. Shift the transmission into position "P", start the engine and let it run at normal idle speed.
Warning! Before starting the engine, carefully check the fan blades for cracks and other damage. Try to keep your hands and the measuring device away from the impeller. Also, avoid taking a position directly in front of the car!
Read the vacuum gauge. On average, the vacuum depth in the intake manifold of a serviceable engine should be fairly stable (without jerking the arrows) and be approximately 432÷560 mm Hg. The following paragraphs provide a diagram for interpreting the readings taken:
1. Low stability of readings may indicate leaks through the gasket between the intake manifold and the cylinder head, or between the manifold and the throttle body. It is also possible that the vacuum hose is not tight enough, or that the (towards lagging behind) ignition timing, or incorrect valve timing. Check the ignition timing using a stroboscope, then eliminate all other possible causes one by one by performing the checks listed in this Chapter, only after that does it make sense to remove the timing cover to check the correct alignment of the timing marks.
2. If the measurement result is 76÷203 mm Hg below the norm and there are fluctuations, the cause of such a deviation may be a leak in the intake manifold gasket in the area of the intake port, or a malfunction of the fuel injection injector.
3. Regular downward deviation of the gauge needle from the stable reading by 51÷102 mm Hg is highly likely to indicate valve leaks. Check the compression pressure in the cylinders.
4. Irregular deviations or resets of readings may be due to valve sticking or misfiring. Measure compression pressure, conduct a leak test, check the condition of the spark plugs.
5. Frequent vibration of the indicator needle within the range of 102 mm Hg at idle speed, accompanied by smoke emission from the exhaust pipe, indicates wear of the valve guide bushings. If the needle begins to vibrate when the engine speed increases, check the intake manifold gasket and cylinder head for signs of leaks. Assess the degree of sagging of the valve springs, check the valves for signs of burnout and try to detect misfires.
; 1 - Stable low reading; 2 - Oscillations of the pointer in the low range of the scale; 3 - Regular drops in indicators; 4 - Irregular drops in indicators; 5 - Frequency of vibration of the arrow; 6 - Fluctuations in a wide range; 7 - Slow fluctuation
6. Minor fluctuations in readings within the range of 25÷51 mm Hg can be considered as evidence of a malfunction of the ignition system. Check the correctness of all standard settings, if necessary, resort to testing using an ignition parameter analyzer.
7. If the gauge needle fluctuates widely, check the compression pressure or perform a leak test to identify a faulty cylinder or a leaky cylinder head gasket.
8. If the needle on the slow speed meter "wanders" over a wide range of the scale, check the PCV system for leaks and idle mixture composition, and also make sure there are no leaks through the carburetor/throttle body gaskets and intake manifold.
9. Estimate the speed of return of the vacuum gauge readings to the initial value when closing the throttle valve after raising the engine speed to a value of approximately 2500 rpm due to rapid opening of the valve. The reading should first fall almost to zero, then rise above the value typical for normal idle speed by approximately 130 mm Hg and return to the idle speed reading again. If the vacuum depth is restored slowly and does not form a peak surge when the throttle valve is abruptly closed, it is necessary to check whether the piston rings are worn. If the readings are returned for a long time, check the patency of the exhaust system (often the muffler or catalytic converter is blocked) – the easiest way is to simply disconnect the suspect section of the exhaust system and repeat the check.