Vehicle engine cooling and lubrication system Honda Fit/Jazz 1
Coolant pump
Examination 1. Remove the drive belt of the attachments. 2. Remove the coolant pump pulley and idler roller. 3. Turn the coolant pump counterclockwise. Make sure it rotates freely. If the pump rotates with difficulty,...
Examination 1. Remove the drive belt of the attachments. 2. Remove the coolant pump pulley and idler roller. 3. Turn the coolant pump counterclockwise. Make sure it rotates freely. If the pump rotates with difficulty,...
Thermostat — removal and installation
Removal 1. Drain the coolant. 2. Remove the air filter assembly. 3. Remove the radiator hoses. 4. Remove the wire holder "A", ground wire "B", wire retainer "C", coolant bypass hose "B" and wire harness retainer "E". 5....
Removal 1. Drain the coolant. 2. Remove the air filter assembly. 3. Remove the radiator hoses. 4. Remove the wire holder "A", ground wire "B", wire retainer "C", coolant bypass hose "B" and wire harness retainer "E". 5....
Radiator — check
1. Check the radiator cap. a) Remove the radiator cap, moisten its gasket with coolant and install it on the tester. b) Apply pressure of 93-123 kPa. c) Make sure the pressure holds. If the pressure drops, replace the...
1. Check the radiator cap. a) Remove the radiator cap, moisten its gasket with coolant and install it on the tester. b) Apply pressure of 93-123 kPa. c) Make sure the pressure holds. If the pressure drops, replace the...
Electric fan of the cooling system
Examination 1. Disconnect the two connectors from the cooling fan motor and the air conditioning system. 2. Apply battery voltage to terminal "2" of the output and ground terminal "1". If the fan does not rotate or...
Examination 1. Disconnect the two connectors from the cooling fan motor and the air conditioning system. 2. Apply battery voltage to terminal "2" of the output and ground terminal "1". If the fan does not rotate or...
Checking the oil pressure sensor
1. Disconnect the connector from the oil pressure sensor. 2. Check the conductivity between the positive terminal and the engine (ground). Make sure that there is conductivity when the engine is off, and there is none...
1. Disconnect the connector from the oil pressure sensor. 2. Check the conductivity between the positive terminal and the engine (ground). Make sure that there is conductivity when the engine is off, and there is none...
Replacing the oil pressure sensor
1. Disconnect the oil pressure sensor connector and unscrew the sensor. 2. Apply a small amount of sealant to 2-3 threads of the oil pressure sensor and install it. Note: Using too much sealant may cause the oil passage...
1. Disconnect the oil pressure sensor connector and unscrew the sensor. 2. Apply a small amount of sealant to 2-3 threads of the oil pressure sensor and install it. Note: Using too much sealant may cause the oil passage...
Checking oil pressure
1. Remove the emergency oil pressure sensor and install a special tool in its place. 2. Start the engine. Stop the engine immediately if the pressure gauge indicates no oil pressure. Repair the lubrication system before...
1. Remove the emergency oil pressure sensor and install a special tool in its place. 2. Start the engine. Stop the engine immediately if the pressure gauge indicates no oil pressure. Repair the lubrication system before...
Disassembly and assembly of the oil pump
Disassembly and assembly of the oil pump. 1 - O-ring seal, 2 - oil pump cover, 3 - driven rotor, 4 - leading rotor, 5 - mounting pin, 6 - oil pump housing, 7 - pressure reducing valve, 8 - spring, 9 - cork.
Disassembly and assembly of the oil pump. 1 - O-ring seal, 2 - oil pump cover, 3 - driven rotor, 4 - leading rotor, 5 - mounting pin, 6 - oil pump housing, 7 - pressure reducing valve, 8 - spring, 9 - cork.
Oil pump — removal and installation
Removal 1. Remove the timing chain. 2. Remove the oil receiver and oil pump. Examination 1. Remove the oil pump cover. 2. Check the gap between the teeth of the leading and driven rotors. Nominal clearance - 0.02 - 0.14...
Removal 1. Remove the timing chain. 2. Remove the oil receiver and oil pump. Examination 1. Remove the oil pump cover. 2. Check the gap between the teeth of the leading and driven rotors. Nominal clearance - 0.02 - 0.14...
Installing an oil separator
1. Clean the damper contact surfaces, bolts and bolt holes. 2. Apply a continuous bead of sealant 1.5mm in diameter to the damper. Note: The parts must be installed within the time specified in the sealant application...
1. Clean the damper contact surfaces, bolts and bolt holes. 2. Apply a continuous bead of sealant 1.5mm in diameter to the damper. Note: The parts must be installed within the time specified in the sealant application...
This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Link in different formats to this section
TEXTHTMLBB Code
- General information
- User manual
- Maintenance
- Power unit
- Engine repair
- Cooling and lubrication system
- Injection and power system
- Control system
- Engine electrical equipment
- Transmission
- Clutch
- Mechanical gearbox
- Automatic gearbox
- Variator (CVT)
- Drive shafts and gearbox
- Chassis and running gear
- Car suspension
- Steering
- Brake system
- Body and interior
- Exterior (external elements)
- Interior (internal elements)
- Doors, locks and windows
- Heater and air conditioner
- Safety system
- Electrical equipment
- Equipment and devices
- Wiring diagrams (since 06.2001)
- Wiring diagrams (since 06.2004)