Car steering Honda CR-V 2

Component arrangement
Component arrangement

Table of signs of malfunction
Find the malfunction symptom in the following table and perform the corresponding procedures in the order given until you find the cause of the malfunction. Sign of malfunction Troubleshooting procedure Also check The...

Fixing Tight Steering
1. Check the power steering. Does the starting load exceed 29 N (3.0 kgf)? Yes. Go to L. 2. No. The amplification is fine. 2. Measure the steady-state liquid pressure at the pump outlet at idle speed. The pressure is...

Checking the steering wheel play
1. Set the front wheels to the straight-ahead position. 2. Measure the distance the steering wheel can be turned left and right without moving the front wheels. If the play is within normal limits, the steering gear and...

Checking the power steering on a stationary vehicle
1. Check the power steering fluid level. 2. Start the engine, let it run at idle speed, turn the steering wheel from lock to lock several times and warm up the fluid. 3. Attach the spring balance to the steering wheel....

Checking the steering drive and steering mechanism
Checking the steering drive and steering mechanism

Checking the pressure in the power steering pump
To determine whether the problem is in the pump or the steering gear, check the fluid pressure as follows: 1. Check the power steering fluid level. 2. Carefully disconnect the pump outlet hose (A) from the pump pipe so...

Checking for Power Steering Fluid Leaks
Checking for fluid leaks

Power Steering Fluid Replacement
Check the reservoir (A) periodically and top up with the recommended fluid if necessary. Use only Genuine Honda Power Steering Fluid. Use of other fluids or automatic transmission fluids may cause increased wear or poor...

Replacing power steering hoses and tubes
Please perform the installation taking into account the following: Connect the hoses securely to the tubes until the hose hits the stop on the tube. Place the clamp or adjustable clamp at the specified distance from the...

Replacing the power steering pump
1. Place a suitable container under the vehicle. 2. Drain the power steering fluid from the reservoir. 3. Remove the drive belt (A) from the pump pulley. 4. Remove the mounting bolts (B) from the pump. 5. Cover the...

Power steering pump repair
Pump disassembled Disassembly Note: When disassembling, please refer to the exploded view image. 1. Remove the power steering pump. 2. Drain the liquid from the pump. 3. Secure the power steering pump (A) in a vice with...

Removal the steering wheel
Note. Components of the optional Inflatable Airbag System (SRS) are located on this site. Before performing repairs or maintenance, review information on the location of SRS system components, precautions, and...

Steering wheel disassembly/assembly
Steering wheel disassembly/assembly

Installing the steering wheel
1. Before installation, make sure the front wheels are in the straight-ahead position, then center the spiral wire (A) by first turning the spiral wire clockwise until it stops. Then turn it counterclockwise about two...

Removal and installation the steering column
Note. Components of the optional Inflatable Airbag System (SRS) are located on this site. Before performing repairs or maintenance, review information on the location of SRS system components, precautions, and...

Checking the operation of the steering column tilt mechanism
1. Move the steering wheel to the straight-ahead position and fully loosen the tilt adjustment lever. 2. Secure the spring balance to the top point of the steering wheel and move the steering column to the lowest...

Checking/Adjusting the Steering Column Tilt Adjustment Lever
Check the steering column ball bearing (A) and steering column pivot bearings (B) for play and smooth rotation. If any bearing rattles or has excessive play, replace the steering column assembly. Check the sliding...

Checking the tilt adjustment lever preload
1. Move the tilt adjustment lever (A) three to five times from the "unlocked" position to the "locked" position; then measure the tilt adjustment lever preload at a distance of 10 mm from the end of the lever. Preload:...

Replacing the steering column lock
1. Remove the steering column. 2. Punch two shear bolts and drill out their heads with a 5mm drill. Be careful not to damage the switch housing when removing the shear bolts. 3. Remove the shear bolts from the switch...

Adjusting the steering rack guide
1. Set the front wheels to the straight-ahead position. 2. On right-hand drive vehicles: remove the air cleaner. Then remove the floor heat shield (A). Be careful not to damage the heater hoses. 3. Loosen the lock nut...

Removal the steering gear
Perform the removal taking into account the following: Using solvent and a brush, wash away oil and dirt from the valve body assembly, its tubes and the end of the steering gear. Blow with compressed air. Before...

Steering gear repair
Steering gear disassembled Note: When disassembling, please refer to the exploded view image. Disassembly 1. Remove the steering gear (see section " Removal the steering gear "). 2. Disconnect the cylinder tubes (A) and...

Installing the steering gear
1. Insert the steering gear cylinder (A) together with the steering rods (B) through the wheel arch opening on the driver's side. 2. Carefully move the steering gear towards the passenger side until the worm shaft...

Replacing the ball joint covers of the steering rods
1. Remove the boot from the tie rod end and wipe off the old grease from the ball joint. 2. Pack the lower portion of the ball pin (A) with fresh multi-purpose grease. 3. Pack the new boot (B) and lip (C) from the...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Link in different formats to this section

TEXTHTMLBB Code