Car gearbox Honda CR-V 1
Manual transmission — dismantling and installation
Dismantling CR-V Models 1. Disconnect the battery from ground. 2. Remove the air filter with the air duct. 3. Disconnect the clutch hydraulic line and remove the clutch slave cylinder. 4. Disconnect the wires from the...
Dismantling CR-V Models 1. Disconnect the battery from ground. 2. Remove the air filter with the air duct. 3. Disconnect the clutch hydraulic line and remove the clutch slave cylinder. 4. Disconnect the wires from the...
Automatic transmission lock switch
The transmission lock switch is part of the combination switch, which also includes the reverse signal switch and gear shift indicator lamp switches. The procedure for removal, installation and adjustment is discussed...
The transmission lock switch is part of the combination switch, which also includes the reverse signal switch and gear shift indicator lamp switches. The procedure for removal, installation and adjustment is discussed...
Automatic transmission (CR-V) — removal and installation
Removal 1. Disconnect the battery from ground, move the transmission selector to position N. 2. Remove the air filter and air duct. 3. Mark and disconnect all wires that prevent transmission removal, disconnect the...
Removal 1. Disconnect the battery from ground, move the transmission selector to position N. 2. Remove the air filter and air duct. 3. Mark and disconnect all wires that prevent transmission removal, disconnect the...
Automatic transmission (Odyssey V6) — removal and installation
Removal 1. Disconnect the battery from ground. 2. Loosen the bolt at the bottom of the windshield washer reservoir. 3. Open the hood and use spacers to secure it in a vertical position. 4. Remove the air filter,...
Removal 1. Disconnect the battery from ground. 2. Loosen the bolt at the bottom of the windshield washer reservoir. 3. Open the hood and use spacers to secure it in a vertical position. 4. Remove the air filter,...
Shift Rod (CR-V and 4-cyl Odyssey)
1. Remove the hatch on the right lower steering column cover. 2. Move the transmission selector to position N. 3. Remove the pin from the cable end and check the alignment of the hole in the cable end with the...
1. Remove the hatch on the right lower steering column cover. 2. Move the transmission selector to position N. 3. Remove the pin from the cable end and check the alignment of the hole in the cable end with the...
Shift Rod (6-Cylinder Odyssey)
1. Remove both steering column covers. 2. Move the transmission selector to position N. 3. Loosen the nut and remove the cable end from the gear shift rod. 4. Pull the cable towards you until it stops and release. Feed...
1. Remove both steering column covers. 2. Move the transmission selector to position N. 3. Loosen the nut and remove the cable end from the gear shift rod. 4. Pull the cable towards you until it stops and release. Feed...
Throttle linkage
1. Start the engine, increase the speed to 3000 rpm, warm up the engine and switch to idle speed. 2. Check the slack in the cable (the cable should deviate in both directions by 10-12 mm). 3. If the slack is not within...
1. Start the engine, increase the speed to 3000 rpm, warm up the engine and switch to idle speed. 2. Check the slack in the cable (the cable should deviate in both directions by 10-12 mm). 3. If the slack is not within...
Transfer case — oil seal replacement
1. Mark the relative position of the shaft relative to the gearbox flange and disconnect the propeller shaft. 2. Unlock the transfer case flange nut by bending back the flange. 3. While holding the flange, loosen the...
1. Mark the relative position of the shaft relative to the gearbox flange and disconnect the propeller shaft. 2. Unlock the transfer case flange nut by bending back the flange. 3. While holding the flange, loosen the...
Transfer case — removal and installation
1. Raise the front of the vehicle. 2. Drain the fluid from the box and remove the mud deflector. 3. Disconnect the transmission cable. 4. Mark the position of the propeller shaft on the transfer case flange and...
1. Raise the front of the vehicle. 2. Drain the fluid from the box and remove the mud deflector. 3. Disconnect the transmission cable. 4. Mark the position of the propeller shaft on the transfer case flange and...
Tightening torques for threaded connections
Tightening torques for threaded connections (Nm) Automatic transmission CR-V and Odyssey 2.2/2.3L models Starter mounting bolt 44 Transmission housing mounting bolt 65 Bolt securing rear engine mount bracket to...
Tightening torques for threaded connections (Nm) Automatic transmission CR-V and Odyssey 2.2/2.3L models Starter mounting bolt 44 Transmission housing mounting bolt 65 Bolt securing rear engine mount bracket to...
This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Link in different formats to this section
TEXTHTMLBB Code
- General information
- User manual
- Technical data
- Maintenance
- Power unit
- Engine repair
- Lubrication system
- Cooling system
- Exhaust system
- Fuel system
- Engine management
- Engine electrical equipment
- Transmission
- Clutch
- Manual gearbox
- Automatic gearbox
- Rear differential
- Drive shafts
- Chassis and running gear
- Steering
- Front suspension
- Rear suspension
- Brake system
- Body and interior
- Exterior (external elements)
- Interior (internal elements)
- Doors, locks and windows
- General information
- Maintenance
- Tips for car owner
- Power unit
- Engine repair
- Engine overhaul
- Cooling and lubrication system
- Engine electrical equipment
- Control system
- Fuel system
- Transmission
- Clutch and drive shafts
- Car gearbox
- Chassis and running gear
- Front suspension
- Rear suspension
- Steering
- Brake system
- Body and interior
- Body service
- Exterior (external elements)
- Interior (internal elements)
- Electrical equipment
- Equipment and devices
- Electrical circuits