Drive shafts of car Honda CR-V 2

Checking drive shafts
1. Check the inner (A) and outer (B) boots on the drive shaft (C) for cracks, damage, grease leakage, and boot clamps (D) for looseness. If any damage is found, replace the boots and clamps. 2. Turn the drive shaft by...

Removal the front drive shafts
1. Loosen the wheel nuts slightly. 2. Raise the front of the vehicle and securely fasten it to the safety stands at the designated points. 3. Loosen the wheel nuts and remove the front wheels. 4. Bend back the locking...

Disassembling the front drive shafts
From the inner hinge side 1. Remove the snap ring from the inner joint. 2. Remove the clamps from the covers. Do not damage the cover and dynamic shock absorber. If the boot clamps are of the welded type (A), cut the...

Replacing the dynamic shock absorber
1. Remove the inner joint. 2. Remove the clamps from the dynamic shock absorber. Do not damage the dynamic shock absorber. If the boot clamps are of the welded type (A), cut the clamp (B). If the boot clamps are of the...

Assembly of front drive shafts
From the inner hinge side 1. To prevent damage to the inner boot, wrap the drive shaft splines with vinyl tape (A). 2. Install the inner boot onto the drive shaft, then remove the vinyl tape. Do not damage the inner...

Installing front drive shafts
1. Place a new snap ring into the groove on the (left) drive shaft. 2. Apply 0.5-1.0 g of the recommended grease to the splined portion (A) of the right drive shaft. After applying grease, remove grease from the spline...

Removal the intermediate shaft
1. Remove the right drive shaft. 2. Remove the heat shield cover. 3. Remove the flange bolt (A) and two mounting bolts (B). 4. Remove the intermediate shaft (A) from the differential. To avoid damaging the differential...

Disassembling the intermediate shaft
1. Remove the snap ring (A), outer oil seal (B) and outer ring clamp (C). 2. Press the intermediate shaft (A) out of the intermediate shaft bearing (B) using a press. 3. Remove the inner ring clamp. 4. Press the...

Assembling the intermediate shaft
1. Thoroughly clean the disassembled parts with solvent and dry with compressed air. Do not wash rubber parts in solvent. 2. Press the intermediate shaft bearing (A) into the bearing support (B) using a special tool and...

Installing the intermediate shaft
1. Thoroughly clean the areas at the junction of the intermediate shaft (A) and the gearbox (differential) solvent or carburetor cleaner and dry with compressed air. Insert the intermediate shaft assembly into the...

Removal the rear drive shafts
1. Loosen the wheel nuts slightly. 2. Raise the rear of the vehicle and securely support it on the safety stands at the designated points. 3. Loosen the wheel nuts and remove the rear wheels. 4. Bend back the locking...

Disassembling the rear drive shafts
Note: Due to the large amount of work involved in replacing one damaged cover, it is advisable to replace both covers at once. These instructions apply to the inner joint. The same procedure applies to the outer joint....

Assembling the rear drive shafts
Note: When assembling, please refer to the exploded view image. Rear drive shafts (disassembled) 1. To prevent damage to the inner boot, wrap the drive shaft splines with vinyl tape (A). 2. Install the inner boot onto...

Installing rear drive shafts
Note: Before installation, make sure that the contact surfaces of the hinge and spline are free of dirt and dust. 1. Install the outer joint (A) onto the rear wheel hub (B). Note: Do not damage the ABS wheel sensor (C)....

Checking the cardan shaft
Universal joint and covers 1. Shift into neutral. 2. Raise the vehicle on all four wheels and securely support it on the safety stands at the designated points. 3. Check that the center support bearing (A) does not have...

Removal the propeller shaft
1. Raise the vehicle on all four wheels and securely support it on the safety stands at the designated points. 2. Remove the protection from the cardan shaft No. 2. 3. Apply marks (A) to the propeller shaft (B) and the...

Installing the cardan shaft
1. Attach the driveshaft (A) to the rear differential (B), aligning the marks (C). 2. Insert the middle support bearing mounting bolts and tighten them. Install new bolts. 3. Attach the propeller shaft (A) to the...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Link in different formats to this section

TEXTHTMLBB Code