Car clutch repair Honda CR-V 2
.
Adjusting the Clutch Pedal and Clutch Pedal Position Switch
Note: For information on checking the clutch pedal position switch, see. in ch. " Cruise control ". Before adjusting the clutch pedal, remove the floor mat from the driver's side. The clutch self-adjusts as it wears. If...
Note: For information on checking the clutch pedal position switch, see. in ch. " Cruise control ". Before adjusting the clutch pedal, remove the floor mat from the driver's side. The clutch self-adjusts as it wears. If...
Replacing the clutch master cylinder
1. Remove the brake fluid from the clutch master cylinder reservoir using a syringe. 2. Remove the retaining clip (A). Disconnect the clutch pipe (B). To prevent brake fluid from leaking out of the clutch pipe, seal its...
1. Remove the brake fluid from the clutch master cylinder reservoir using a syringe. 2. Remove the retaining clip (A). Disconnect the clutch pipe (B). To prevent brake fluid from leaking out of the clutch pipe, seal its...
Clutch Master Cylinder Repair
Note: When connecting the hose to the tank, align the yellow mark on the hose with the protrusion on the tank connection area. When connecting the reservoir hose, align the blue mark on the hose with the protrusion on...
Note: When connecting the hose to the tank, align the yellow mark on the hose with the protrusion on the tank connection area. When connecting the reservoir hose, align the blue mark on the hose with the protrusion on...
Replacing the clutch slave cylinder
Note: To avoid damage to the paintwork, cover the fenders with protective aprons. Do not spill brake fluid on your vehicle; it can ruin the paint; if brake fluid gets on the paint, wash it off immediately with water. 1....
Note: To avoid damage to the paintwork, cover the fenders with protective aprons. Do not spill brake fluid on your vehicle; it can ruin the paint; if brake fluid gets on the paint, wash it off immediately with water. 1....
Clutch replacement
Removal the pressure plate and driven clutch disc 1. Check the height of the diaphragm spring tips using the indicator (A). If the height exceeds the permissible limit, replace the pressure plate. Standard (new) 0.6 mm...
Removal the pressure plate and driven clutch disc 1. Check the height of the diaphragm spring tips using the indicator (A). If the height exceeds the permissible limit, replace the pressure plate. Standard (new) 0.6 mm...
Checking the flywheel
1. Check the ring gear teeth for wear or damage. 2. Check for wear, cracks and overheating on the contact surface of the flywheel under the driven clutch disc. 3. Measure the flywheel runout (A) using a dial indicator...
1. Check the ring gear teeth for wear or damage. 2. Check for wear, cracks and overheating on the contact surface of the flywheel under the driven clutch disc. 3. Measure the flywheel runout (A) using a dial indicator...
Flywheel replacement
1. Install the special tool as shown in the figure. 2. Loosen the flywheel mounting bolts crosswise in several passes and remove the flywheel. 3. Install the flywheel onto the crankshaft and tighten the mounting bolts...
1. Install the special tool as shown in the figure. 2. Loosen the flywheel mounting bolts crosswise in several passes and remove the flywheel. 3. Install the flywheel onto the crankshaft and tighten the mounting bolts...
Installing the pressure plate and driven clutch disc
1. Install the ring gear holder. 2. Apply Urea Grease UM264 (41211-PY5-305) onto the splines (A) of the clutch driven disc (B), then install the clutch driven disc using the special tool as shown in the figure. 3....
1. Install the ring gear holder. 2. Apply Urea Grease UM264 (41211-PY5-305) onto the splines (A) of the clutch driven disc (B), then install the clutch driven disc using the special tool as shown in the figure. 3....
Replacing the release bearing
1. Remove the release fork boot (A) from the clutch housing (B). 2. Remove the release fork (C) from the clutch housing (B) by compressing the release fork mounting spring (D) with pliers. Remove the release bearing...
1. Remove the release fork boot (A) from the clutch housing (B). 2. Remove the release fork (C) from the clutch housing (B) by compressing the release fork mounting spring (D) with pliers. Remove the release bearing...
This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Link in different formats to this section
TEXTHTMLBB Code
- General information
- User manual
- Technical data
- Maintenance
- Power unit
- Engine repair
- Lubrication system
- Cooling system
- Exhaust system
- Fuel system
- Engine management
- Engine electrical equipment
- Transmission
- Clutch
- Manual gearbox
- Automatic gearbox
- Rear differential
- Drive shafts
- Chassis and running gear
- Steering
- Front suspension
- Rear suspension
- Brake system
- Body and interior
- Exterior (external elements)
- Interior (internal elements)
- Doors, locks and windows
- General information
- Maintenance
- Tips for car owner
- Power unit
- Engine repair
- Engine overhaul
- Cooling and lubrication system
- Engine electrical equipment
- Control system
- Fuel system
- Transmission
- Clutch and drive shafts
- Car gearbox
- Chassis and running gear
- Front suspension
- Rear suspension
- Steering
- Brake system
- Body and interior
- Body service
- Exterior (external elements)
- Interior (internal elements)
- Electrical equipment
- Equipment and devices
- Electrical circuits