Exterior (external body elements) of the car Honda CR-V 1

Doors — removal and installation
The procedure for removing and installing the front and rear doors is no different. Removal 1. Disconnect the battery from ground. 2. Place a jack under the door and support the door using a board. 3. Loosen the limiter...

Doors — adjustment
When the door is adjusted correctly, the door panel should be flush with the adjacent body panels, and the gap between the door and the body should be the same around the entire door contour. In addition, when closing...

Hood — removal, installation and adjustment
1. Open the hood. 2. Disconnect the battery from ground. 3. Outline the contours of the hood hinges. 4. Disconnect the windshield washer hoses and wires that may interfere with the removal of the hood. 5. Ask an...

Rear Body Door (CR-V Models) — Removal and Installation
Removal 1. Disconnect the battery from ground. 2. Support the lid with a jack through a board. 3. Loosen the limiter lever mounting bolts. 4. Remove the door trim panel, remove the latches and disconnect the connectors....

Rear Compartment Lid (4-cylinder Odyssey)
1. Disconnect the battery from ground. 2. Open the lid and place a support underneath it. 3. Remove the side window trim from the latches. 4. Remove the side caps from the lid handle, unscrew the screws and remove the...

Rear Compartment Lid (6-cylinder Odyssey)
1. Disconnect the battery from ground. 2. Open the lid and place a support underneath it 3. Remove the side caps from the lid handle, unscrew the screws and remove the lid. 4. Remove the latches and brackets and remove...

Bumpers (CR-V models) — removal and installation
Front bumper 1. Disconnect the battery from ground. 2. Remove the radiator grille (see below). 3. Pry up and remove the clips along the top of the bumper (photo). 4. Remove the self-tapping screws from the bottom and...

Bumpers (Odyssey models) — removal and installation
Front bumper 1. Disconnect the battery from ground. 2. Remove the bolt and screw at the bottom of the bumper, which are located just in front of the wheel arch (the screw secures the bumper to the rear lower edge). 3....

Radiator grille — removal and installation
CR-V 1. Disconnect the battery from ground. 2. Using a flat, thin tool, pry up and remove the plastic cover on the top of the grille emblem. 3. Using a sufficiently long screwdriver, remove the screws from the grille...

Exterior Mirrors (CR-V) — Removal and Installation
Mirror assembly 1. Disconnect the battery from ground. 2. Lower the door glass and release the triangular mirror cover from the latches by hand. 3. Disconnect the connector. 4. Loosen the mounting bolts and remove the...

Exterior Mirrors (4-cylinder Odyssey) — Removal and Installation
Mirror assembly 1. Disconnect the battery from ground. 2. Remove the inner door panel (see below). 3. Stick a strip of tape on the bottom of the mirror, then pry up the bottom of the cover, move it away and unscrew the...

Exterior Mirrors (Odyssey V6) — Removal and Installation
Mirror assembly 1. Disconnect the battery from ground. 2. Lower the door glass. 3. Carefully, without using tools, remove the upper part of the inner decorative trim of the mirror from the latches, lift and remove the...

Radio Antenna — Replacement
CR-V 1. Remove the instrument panel sections that obstruct access to the antenna cable (See Chapter 6 ). 2. Loosen the antenna mounting screws using a T-20 Torx screwdriver. 3. Installation is carried out in reverse...

Wing — removal and installation
1. Disconnect the battery from ground. 2. Open the hood. 3. Remove the radiator grille and front bumper. 4. Remove the fender trim panel by removing the 2 clips (to do this, remove the finger and remove the latch...

Side panel of the body threshold — removal and installation
1. Remove the screws at the rear bottom of the front wheel well. 2. Remove the pins and pull out the latch bushings along the bottom of the sill panel. 3. Push the panel forward and remove. 4. Remove the L-shaped...

Sunroof — Removal and Installation
4-cylinder Odyssey Replacing the hatch 1. Open the hatch halfway. 2. Feed the front part of the hatch trim by pushing it down. 3. Move the bezel back, remove the pins from the holder and remove the bezel. 4. Unscrew the...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Link in different formats to this section

TEXTHTMLBB Code