Front suspension and wheels of the car Honda CR-V 1

Wheel — removal and installation
Removal 1. Place the jack under the support area (see vehicle owner's manual). 2. Set the car to the handbrake and block diagonally opposite wheels. 3. On vehicles with automatic transmission, set the transmission...

Checking the condition of tires and wheels
Check the condition of the tires, check for wear and damage, remove any sharp objects stuck in them; check the pressure. Check the wheel rim for corrosion, dents, cracks and other damage. Replace or repair damaged parts...

Wheel nut studs — replacement
Front wheels Removal 1. Remove the steering knuckle (see below). 2. On CR-V and Odyssey V6 models, press the front hub out of the bearing assembly. 3. On 4-cylinder Odysseys, remove the mounting bolts and remove the...

Front suspension parts
Front Suspension Parts (CR-V): 1. Steering knuckle; 2. Tie rod end; 3. Lower arm; 4. Upper arm; 5, 6. Bushings; 7. Anti-roll bar; 8. Upper ball joint; 9. Shock absorber fork; 10. Lower ball joint Front suspension (CR-V,...

Springs — removal and installation
1. Remove the rack. 2. Install the compressor and compress the spring. Loosen the upper mount nut (photo), remove the upper strut cover, then remove the spring. 3. Installation is carried out in reverse order. Replace...

Rack — removal and installation
Removal 1. Raise the vehicle. 2. Remove the front wheels. 3. Unscrew the hose bracket mounting bolts on the stand. 4. Loosen the fork-to-shock absorber clamp bolt, then the fork-to-lower arm bolt and remove the fork. 5....

Upper Ball Joint — Inspection (CR-V and 4-cyl Odyssey)
The upper ball joint and suspension arm are a non-separable structure. If the ball joint fails, replace the upper control arm assembly. 1. Raise the vehicle. 2. Raise the lower arm with a jack by 50 mm. 3. Rock the...

Lower ball joint — check
1. Raise the vehicle. 2. Raise the lower arm with a jack by 50 mm. 3. Rock the wheel in a vertical plane, pushing it towards you and away from you. 4. If any play is detected, insert a pry bar between the steering...

Lower ball joint — removal and installation
Caution: On Odyssey V6 vehicles, the lower ball joint and control arm are a one-piece assembly. If the ball joint fails, replace the lower arm assembly. CR-V and 4-cylinder Odyssey Removal 1. Remove the brake caliper...

Anti-roll bar — removal and installation
1. Mark the position of the stabilizer. 2. Disconnect the rods at the ends of the stabilizer bar. 3. Remove the stabilizer bushing brackets. 4. Remove the stabilizer. 5. Installation is carried out in reverse order....

Suspension Rod (4-Cylinder Odyssey) — Removal and Installation
Removal 1. Loosen the wheel mounting bolts. 2. Raise the car. 3. Unscrew the suspension rod nut on the subframe. 4. Unscrew the suspension rod fasteners on the lower arm. 5. Remove the barbell. Installation 6. Lubricate...

Upper Control Arm (4-Cylinder Odyssey and CR-V) — Removal and Installation
Removal 1. Raise the vehicle. 2. Remove the front wheels. Place a jack under the lower arm. 3. Remove the lower strut mount fork. 4. Press the ball joint out of the steering knuckle. 5. Disconnect the brake hose...

Lower control arm — removal and installation
Removal 1. Loosen the wheel nuts. 2. Raise the car. 3. Remove the front wheels. 4. On CR-V and 6-cylinder Odyssey vehicles, disconnect the lower stabilizer link and remove the strut yoke through bolt 5. On 4-cylinder...

Lower arm bushings — replacement
The lower suspension arm is a non-separable structure. If the bushings are worn or damaged, replace the upper arm. Only the rear lower control arm bushings are changed on CR-V models. 1. Remove the lower arm front...

Steering knuckle — removal and installation
Steering knuckle (Odyssey V6)Steering knuckle (Odyssey V6): 1. Shock absorber tightening bolt; 2. Nut; 3. Bearing (replace); 4. Spring ring; 5. Mud deflector; 6. Screw with washer; 7. Brake disc mounting screw; 8. Cap;...

Front hub and bearing
Examination 1. Raise the vehicle. 2. Remove the front and/or rear wheels. 3. Re-install the wheel nuts and tighten to 108 Nm. 4. Check the bearing axial play, which is measured on the hub flange. The rear bearing axial...

Wheel angle adjustment
The vehicles in question are equipped with front and rear wheel alignment adjustments (some vehicles also have rear wheel camber adjustment). The steering axis angle on 4-cylinder Odysseys is adjusted by installing...

Tightening torques for threaded connections
Tightening torques for threaded connections (Nm) Hub Nut 245 Wheel mounting nuts (front and back) 109 Self-locking nut of the shock absorber rod of the strut CR-V-2.2L/2.3L Odyssey 29 3.5L Odyssey 44 Strut mounting nuts...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Link in different formats to this section

TEXTHTMLBB Code