Car rear suspension Honda CR-V 1
Rear suspension parts
Rear suspension parts (CR-VJ: 1. Shock absorber; 2. Upper arm; 3. Stabilizer link; 4. Half shaft; 5. Bushing; 6. Spring; 7. Lower arm; 8. Trailing arm Rear suspension parts (Odyssey V-6): 1. Trailing arm; 2. Lower arm...
Rear suspension parts (CR-VJ: 1. Shock absorber; 2. Upper arm; 3. Stabilizer link; 4. Half shaft; 5. Bushing; 6. Spring; 7. Lower arm; 8. Trailing arm Rear suspension parts (Odyssey V-6): 1. Trailing arm; 2. Lower arm...
Rear suspension — design description
Caution: On 4-cylinder Odysseys, after removing and installing any rear suspension component, check and adjust the metering valve spring length ( see Ch. 9 ). Rear suspension (4-cylinder Odyssey): 1. Nut. Hold the nut...
Caution: On 4-cylinder Odysseys, after removing and installing any rear suspension component, check and adjust the metering valve spring length ( see Ch. 9 ). Rear suspension (4-cylinder Odyssey): 1. Nut. Hold the nut...
Springs — removal and installation
CR-V Cars 1. Raise the vehicle. 2. Remove the rear wheels. 3. Remove the stand (see below). 4. Place the stand in a vice and compress the spring with a compressor. 5. Unscrew the self-locking nut. 6. Remove the washer,...
CR-V Cars 1. Raise the vehicle. 2. Remove the rear wheels. 3. Remove the stand (see below). 4. Place the stand in a vice and compress the spring with a compressor. 5. Unscrew the self-locking nut. 6. Remove the washer,...
Shock absorbers — removal and installation
4-cylinder Odyssey Removal 1. Remove the cup holder from the top of the right rear side trim panel. From the left rear side panel, remove the cup holder, storage tray and jack. 2. Raise the car. 3. Remove the rear...
4-cylinder Odyssey Removal 1. Remove the cup holder from the top of the right rear side trim panel. From the left rear side panel, remove the cup holder, storage tray and jack. 2. Raise the car. 3. Remove the rear...
Rack (CR-V) — Removal and Installation
1. Raise the vehicle and remove the rear wheels. 2. Remove the side hatch cover in the cargo compartment (photo). 3. Unscrew the rack mounting bolts through the hatch opening. 4. Unscrew the bolt securing the strut to...
1. Raise the vehicle and remove the rear wheels. 2. Remove the side hatch cover in the cargo compartment (photo). 3. Unscrew the rack mounting bolts through the hatch opening. 4. Unscrew the bolt securing the strut to...
Rear suspension arms — removal and installation
CR-V Upper arm 1. Raise the vehicle and remove the rear wheel. 2. Unscrew the bolts securing the lever to the body. Remove the lever. 3. Installation is carried out in reverse order. Lubricate the bushing from the body...
CR-V Upper arm 1. Raise the vehicle and remove the rear wheel. 2. Unscrew the bolts securing the lever to the body. Remove the lever. 3. Installation is carried out in reverse order. Lubricate the bushing from the body...
Anti-roll bar — removal and installation
1. Mark the position of the stabilizer. 2. Disconnect the stabilizer rods. 3. Remove the stabilizer brackets from the bottom of the car. 4. Remove the stabilizer. 5. Installation is carried out in reverse order....
1. Mark the position of the stabilizer. 2. Disconnect the stabilizer rods. 3. Remove the stabilizer brackets from the bottom of the car. 4. Remove the stabilizer. 5. Installation is carried out in reverse order....
Rear Hub and Bearings (CR-V)
Rear hub: 1, 9. Bolt; 2. Sealing ring (replace).; 3. Brake shield; 4. Hub nut (replace, after tightening, lock the nut); 5. Pads; 6. Wheel nut; 7. Brake drum; 8. Rear hub (check for damage); 10. Hub bearing (replace);...
Rear hub: 1, 9. Bolt; 2. Sealing ring (replace).; 3. Brake shield; 4. Hub nut (replace, after tightening, lock the nut); 5. Pads; 6. Wheel nut; 7. Brake drum; 8. Rear hub (check for damage); 10. Hub bearing (replace);...
Rear Hub and Bearings (Odyssey)
Rear hub (4-cylinder Odyssey): 1, 13 Nut; 2. Fist; 3. O-ring (replace); 4. Brake shield; 5. Washer; 6. Hub nut; 7. Wheel mounting nut; 8. Wheel cover; 9. Hub cap (replace); 10. Screw; 11. Brake disc; 12. Hub Attention!...
Rear hub (4-cylinder Odyssey): 1, 13 Nut; 2. Fist; 3. O-ring (replace); 4. Brake shield; 5. Washer; 6. Hub nut; 7. Wheel mounting nut; 8. Wheel cover; 9. Hub cap (replace); 10. Screw; 11. Brake disc; 12. Hub Attention!...
Tightening torques for threaded connections
Tightening torques for threaded connections (Nm) Hub Nut CR-V 181 Odyssey 245 Rear suspension strut CR-V Self-locking nut of the shock absorber rod 29 Strut mounting nut 49 Through bolt securing the strut to the lower...
Tightening torques for threaded connections (Nm) Hub Nut CR-V 181 Odyssey 245 Rear suspension strut CR-V Self-locking nut of the shock absorber rod 29 Strut mounting nut 49 Through bolt securing the strut to the lower...
This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Link in different formats to this section
TEXTHTMLBB Code
- General information
- User manual
- Technical data
- Maintenance
- Power unit
- Engine repair
- Lubrication system
- Cooling system
- Exhaust system
- Fuel system
- Engine management
- Engine electrical equipment
- Transmission
- Clutch
- Manual gearbox
- Automatic gearbox
- Rear differential
- Drive shafts
- Chassis and running gear
- Steering
- Front suspension
- Rear suspension
- Brake system
- Body and interior
- Exterior (external elements)
- Interior (internal elements)
- Doors, locks and windows
- General information
- Maintenance
- Tips for car owner
- Power unit
- Engine repair
- Engine overhaul
- Cooling and lubrication system
- Engine electrical equipment
- Control system
- Fuel system
- Transmission
- Clutch and drive shafts
- Car gearbox
- Chassis and running gear
- Front suspension
- Rear suspension
- Steering
- Brake system
- Body and interior
- Body service
- Exterior (external elements)
- Interior (internal elements)
- Electrical equipment
- Equipment and devices
- Electrical circuits