Car steering Honda Accord 3
Inflatable Airbag System (SRS)
Some 1991 Accord models are equipped with the Supplemental Restraint System (SRS) (often referred to as an air bag). The air bag is located directly inside the steering wheel hub; sensors and control unit - behind the...
Some 1991 Accord models are equipped with the Supplemental Restraint System (SRS) (often referred to as an air bag). The air bag is located directly inside the steering wheel hub; sensors and control unit - behind the...
Steering wheel — removal and installation
All models without inflatable cushions 1. Disconnect the negative cable from the battery. 2. Remove the decorative cover from the steering wheel. Disconnect the necessary electrical connectors underneath it. 3. Make...
All models without inflatable cushions 1. Disconnect the negative cable from the battery. 2. Remove the decorative cover from the steering wheel. Disconnect the necessary electrical connectors underneath it. 3. Make...
Steering column — removal and installation
1. Disconnect the negative cable from the battery. 2. Remove the steering wheel. 3. Remove the lower cover. Remove the driver's knee bolster, if present. 4. Remove the top and bottom covers of the column. 5. Disconnect...
1. Disconnect the negative cable from the battery. 2. Remove the steering wheel. 3. Remove the lower cover. Remove the driver's knee bolster, if present. 4. Remove the top and bottom covers of the column. 5. Disconnect...
Rack and worm (direct acting steering)
Removal 1. Raise and securely support the front of the vehicle. Double check that the mount is secure. 2. Remove the steering joint cover and casing. Unscrew the bolt and separate the steering shaft at the coupling. 3....
Removal 1. Raise and securely support the front of the vehicle. Double check that the mount is secure. 2. Remove the steering joint cover and casing. Unscrew the bolt and separate the steering shaft at the coupling. 3....
Rack and worm (power steering)
Removal 1. Disconnect the negative battery cable. Raise and secure the vehicle. 2. Remove the cover from the steering joint and disconnect the steering column. 3. Drain the fluid by disconnecting the crankcase return...
Removal 1. Disconnect the negative battery cable. Raise and secure the vehicle. 2. Remove the cover from the steering joint and disconnect the steering column. 3. Drain the fluid by disconnecting the crankcase return...
Steering adjustment
You will need Honda special tool 07916-SA50001 for the steering gear housing lock nuts or equivalent. Accord 1. Remove the steering gear mud shield, if equipped. 2. Loosen the rack guide adjusting lock nut. 3. Tighten...
You will need Honda special tool 07916-SA50001 for the steering gear housing lock nuts or equivalent. Accord 1. Remove the steering gear mud shield, if equipped. 2. Loosen the rack guide adjusting lock nut. 3. Tighten...
4-wheel steering system (4WS)
The 4WS Prelude uses a front rack and pinion steering system with an additional output worm. The output worm is connected to the rear steering box via a central shaft. When the steering wheel is turned, the rack and...
The 4WS Prelude uses a front rack and pinion steering system with an additional output worm. The output worm is connected to the rear steering box via a central shaft. When the steering wheel is turned, the rack and...
4 Wheel Steering System — Removal and Installation
The use of Honda special tool 07HAJ-SF1020A for the Center Lock Pin is required. It should always be installed when removing the rear steering case or center shaft. It should also be used when aligning the rear wheels....
The use of Honda special tool 07HAJ-SF1020A for the Center Lock Pin is required. It should always be installed when removing the rear steering case or center shaft. It should also be used when aligning the rear wheels....
Power steering pump — removal and installation
1. Drain the fluid from the system as follows: a. Disconnect the pump return hose from the tank and place the end in a large container. Plug the channel in the tank. b. Start the engine and let it run at a fast idle....
1. Drain the fluid from the system as follows: a. Disconnect the pump return hose from the tank and place the end in a large container. Plug the channel in the tank. b. Start the engine and let it run at a fast idle....
Adjusting the power steering pump belt
1. Apply approximately 10 kg of pressure to the belt midway between the pulleys. The belt sag should be as follows: 1984-89 Accord - 14-17 mm, 1984-87 Prelude - 14-17 mm, 1990-91 Accord - 12.5-16 mm, 1988-91 Prelude -...
1. Apply approximately 10 kg of pressure to the belt midway between the pulleys. The belt sag should be as follows: 1984-89 Accord - 14-17 mm, 1984-87 Prelude - 14-17 mm, 1990-91 Accord - 12.5-16 mm, 1988-91 Prelude -...
Bleeding the steering system
1. Make sure the tank is filled to the FULL mark; don't overfill it. 2. Start the engine and let it idle. 3. Turn the steering wheel from side to side several times, lightly touching the stops. 4. Turn off the engine....
1. Make sure the tank is filled to the FULL mark; don't overfill it. 2. Start the engine and let it idle. 3. Turn the steering wheel from side to side several times, lightly touching the stops. 4. Turn off the engine....
This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Link in different formats to this section
TEXTHTMLBB Code
- General information
- Introduction to the guide
- User manual
- Maintenance
- Power unit
- Four-cylinder engines
- Six-cylinder engines
- Engine overhaul
- Cooling system
- Heater and air conditioner
- Power and exhaust systems
- Engine electrical equipment
- Engine management
- Transmission
- Mechanical gearbox
- Automatic gearbox
- Clutch and drive shafts
- Chassis and running gear
- Brake system
- Car suspension
- Steering
- Body and interior
- Exterior (external elements)
- Interior (internal elements)
- Electrical equipment
- Equipment and devices
- Electrical circuits
- General information
- Maintenance
- Power unit
- Engine adjustment
- Engine repair
- Engine electrics
- Emission management
- Engine management (carburetor)
- Electronic injection
- Programmable injection
- Schematic of emission system
- Fuel system
- Feedback management
- Transmission
- Manual gearbox
- Automatic gearbox
- Clutch
- Chassis and running gear
- Front suspension
- Rear suspension
- Steering
- Brake system
- Electrical equipment
- Ventilation and heating
- Air conditioner
- Cruise control system
- Equipment and devices