Drive shafts and rear gearbox of the car Honda Fit/Jazz 1

Cardan shaft — check
1. Perform general checks. a) Shift into neutral. b) Jack up the car. c) Loosen the bolts (B), disconnect the fasteners (A) and remove the bracket (C). c) By rocking the propeller shaft (D), check that there is no...

Cardan shaft — removal and installation
Note: Installation is carried out in the reverse order of removal. Tightening torques are given in the text. 1. Jack up the car. 2. Remove the engine exhaust pipe. Tightening torque - 22 Nm 3. Apply marks (C) to the...

Checking and changing oil
Checking the level 1. Place the vehicle on a flat, horizontal surface. 2. Unscrew the filler plug (A) and remove the gasket (B). 3. Make sure that the oil level in the crankcase is below the filler plug hole. If...

Rear axle (4WD) — removal
Rear gearbox supports. 1 - support "B", 2 - washers; 3 - support bracket "A", 4 - support "A1", 5 - gearbox. 1. Jack up the car. 2. Remove the engine exhaust pipe. 3. Drain the oil from the rear gearbox. 4. Apply marks...

Rear Gearbox (4WD) — Installation
1. Install supports (B) and (C) on the gearbox. Tightening torque: support bolts "B" - 59 Nm support bolts "C" - 49 Nm 2. Install the rear gearbox on the jack. 3. Install new snap rings (A) onto the drive shafts. While...

Rear gearbox (4WD) — disassembly and assembly
Note: disassemble and assemble in accordance with the figure "Rear gearbox". Rear gearbox. 1 - nut, 2 - washer, 3 - support ring, 4 - flange, 5 - rear gearbox cover, 6 - pin, 7 - gearbox output shaft, 8 - coupling, 9 -...

Drive shafts — check
1. Check the inner (A) and outer (B) hinge boot for cracks and damage. Replace the boots (A and B) and boot clamps (C) if necessary. 2. Check that the boot clamps (C) are not loose and that there are no grease leaks....

Front Drive Shafts — Removal
Note: Apply the parking brake before starting work. 1. Jack up the car. 2. Loosen the front wheel mounting nuts (A). 3. Drain the automatic transmission (CVT) working fluid or manual transmission oil (see chapter "...

Front Drive Shafts — Disassembly
Disassembly and assembly of front drive shafts (left-hand drive models). 1 - retaining ring, 2 - outer race of the inner joint, 3 - roller, 4 - internal hinge, 5 - clamp (type 1), 6 - clamp, (type 2), 7 - inner hinge...

Front Drive Shafts — Assembly
Disassembly and assembly of front drive shafts (right-hand drive models). 1 - retaining ring, 2 - outer race of the inner joint (left shaft), 3 - outer race of the inner joint (right shaft), 4 - roller, 5 - internal...

Front Drive Shafts — Installation
1. (Left hand drive models) Apply grease to the contact surface of the outer joint and the front wheel bearing. 2. Install the retaining ring onto the drive shaft or intermediate drive shaft. 3. (Left hand drive models)...

Front Intermediate Drive Shaft — Removal
(Models with left-hand drive and automatic transmission) 1. Drain the automatic transmission fluid (see chapter " Maintenance and general check and adjustment procedures "). 2. Remove the right drive shaft (see section...

Front Intermediate Drive Shaft — Disassembly
Disassembly and assembly of the intermediate drive shaft. 1 - ring, 2 - intermediate drive shaft, 3 - thrust ring, 4 - internal retaining ring, 5 - bearing, 6 - bolt, 7 - bracket, 8 - outer retaining ring, 9 - oil seal,...

Front Intermediate Drive Shaft — Assembly
1. Clean the contact surfaces of the removed parts. 2. Using special tools, press the bearing (B) into the bracket (A). 3. Install the inner snap ring. 4. Using a press and special tool (C), press the intermediate shaft...

Front Intermediate Drive Shaft — Installation
(Models with left-hand drive and automatic transmission) Install the intermediate drive shaft (A). Note: When installing, hold the intermediate drive shaft in a horizontal position so that the sharp splines of the shaft...

Rear Drive Shafts — Removal
Note: Before starting work, install wheel chocks. 1. Jack up the car. 2. Unscrew the rear wheel mounting nuts. 3. Remove the rear wheels. 4. Disconnect the drive shaft from the gearbox output shaft. 5. Remove the brake...

Rear Drive Shafts — Disassembly
Disassembly and assembly of rear drive shafts: 1 - retaining ring, 2 - outer race of the inner joint, 3 - inner race of the inner joint, 4 - separator, 5 - ball, 6 - clamp, 7 - inner hinge cover, 8 - drive shaft, 9 -...

Rear Drive Shafts — Assembly
Inner hinge 1. Wind the protective tape (C) onto the drive shaft (A). 2. Install the boot (B) onto the drive shaft. 3. Remove the protective tape. 4. Align the marks (D) on the drive shaft (A), the inner race (B) of the...

Rear Drive Shafts — Installation
1. Install the drive shaft (B) into the rear wheel hub (A). Note: Do not damage the wheel speed sensor when installing the drive shaft. 2. Connect the drive shaft assembly with the hub to the steering knuckle and...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Link in different formats to this section

TEXTHTMLBB Code