Car automatic transmission Honda Avancier 1

PGM-FI Control Unit Pin Locations
32-pin connector A 25-pin connector B 31-pin connector C 16-pin D connector

Electrical fault diagnostics — diagnostic description
The PGM-Fi control unit (which combines PGM-Fi control and automatic transmission control) has a self-diagnosis function. If a malfunction is detected in the system (ignition key in the ON (II) position), the D...

Torque Converter Lockup Solenoid Valve and Shift Solenoid Valve Assy — Check
Caution: Do not damage or deform the connector during testing. 1. Disconnect the connector of the lock-up solenoid valve and the shift solenoid valve A. 2. Measure the resistance between the corresponding connector...

Torque Converter Lockup Solenoid Valve and Shift Solenoid Valve Assembly — Replacement
1. Unscrew 3 bolts (6 x 1.0 mm) and remove the locking solenoid valve and gear shift solenoid valve A. 2. Clean the installation area of the solenoid valves and oil channels. Make sure there is no contamination. 3....

Shift Solenoid Valves B and C — Check
1. Disconnect the connector of the electronic shift valve B or C. 2. Check the resistance between contacts 1 and 2 of the connector. Standard resistance: 12-25 Δ If the resistance is different from the above, replace...

Electric valves B and C of gear shifting — replacement
Attention: If you replace solenoid valves B and C at the same time, remember their installation locations. The connector for solenoid valve B is black, and for solenoid valve C it is brown. 1. Unscrew the bolt (6 x 1.0...

Automatic transmission clutch pressure solenoid valves A and B — checking
1. Disconnect the connector of the A and B pressure solenoid valves in the automatic transmission clutch. 2. Measure the resistance between pins 1 and 2 of each connector. Standard resistance: approx. 5.0 Δ If the...

Electric valves A and B of pressure in the automatic transmission clutch — replacement
1. Unscrew 6 bolts (6 x 1.0 mm) and remove the A and B pressure solenoid valves in the automatic transmission clutch as an assembly. 2. Clean the installation area of the solenoid valves and oil channels. Make sure...

Intermediate and secondary shaft speed sensors — replacement
1. Disconnect the connectors and remove the intermediate and secondary shaft speed sensors. 2. Install new O-rings. Then install the sensors. 3. Make sure there is no rust, oil, dirt, etc. inside the connectors. Install...

Pressure switches in 2nd and 3rd gear clutches — replacement
1. Disconnect the connector and remove the switch. 2. Install a new sealing washer, then install the switch. 3. Tighten the switch to the required torque. Attention: When tightening, use the key to secure only the metal...

Switch D3 and Switch Low hold — replacement
1. Remove the lower front console panel and the audio system panel (to remove the Low Hold switch) see chapter Body ). 2. Remove the electrical wiring clamp and disconnect the switch connectors. 3. Remove switch D3 from...

Automatic transmission selector lever switch — replacement
Caution: Install the jack and stands only in designated areas. 1. Apply the parking brake, chock the rear wheels. Jack up the front wheels and place the car on supports. 2. Set the selector lever to position N. 3....

Automatic transmission selector lever switch — check
After repairing the automatic transmission, perform a final check on the vehicle, which includes checking the gear shift timing and the operation of the automatic transmission in each range. Final check 1. Apply the...

Automatic transmission oil — check
1. Place the car on a horizontal surface, start the engine, and warm it up until the radiator fan turns on for the 2nd time. Then turn off the engine. 2. Remove the automatic transmission dipstick, wipe it with a clean...

Automatic transmission oil — replacement
1. Place the car on a horizontal surface, unscrew the drain plug and drain the oil. 2. Replace the sealing washer and tighten the drain plug. 3. Fill the automatic transmission with new oil through the dipstick hole....

Automatic transmission oil — oil pressure
Examination 1. Check the automatic transmission oil level. 2. 2WD models: Apply the parking brake and chock the rear wheels. Jack up the front wheels and support the vehicle so that the front wheels can turn. 4WD...

Automatic transmission oil cooler hoses — installation
1. Place the automatic transmission oil cooler hoses on the tubes and secure with clamps as shown in the figure. Caution: Make sure that the clamp fastening does not touch adjacent components. 2. Secure the oil cooler...

Automatic transmission selector lever — removal
1. Remove the lower front console panel and the audio system panel (to remove the Low Hold switch, see chapter Body ). 2. Remove the wiring clamps and disconnect the connectors of the D3 and Low Hold switches, as well...

Automatic transmission selector lever — disassembly and assembly
Before assembly, apply lubricant to the following parts: Moving parts of the selector lever Moving parts of the shift lock mechanism

Automatic transmission selector lever — installation
1. Install the selector lever assembly. 2. Turn the holder 90° counterclockwise, insert into the bracket, turn 90° clockwise and secure the holder. Install the cable by holding the holder, not the tube. Before turning...

Control cable — adjustment
1. Remove the lower panel of the front console, see chapter Body . 2. Set the selector lever to position R. 3. Unscrew the nut of the control cable end. 4. Turn the ignition key to the ON (II) position and check the R...

Control cable — replacement
Caution: Install the jack and stands only in designated areas. 1. Remove the lower front console panel. 2. Set the selector lever to position R and unscrew the control cable end nut. 3. Turn the holder 90°...

Transfer case (4WD) — checking for play
1. Set the selector lever to position N. 2. Disconnect the propeller shaft from the transfer case. Apply alignment marks to the contact surfaces of the propeller shaft and transfer case. 3. Install the indicator on the...

Transfer Case (4WD) — Check for Oil Leaks
Check the transfer case for oil leaks. If there is a leak from under the box cover, remove the cover and replace the O-rings. If there is a leak at the point where the transfer case and torque converter meet, remove the...

Transfer case (4WD) — replacement
Attention: Install the jack and stands only in designated places. 1. Unscrew the drain plug and drain the oil. 2. Replace the sealing washer and tighten the drain plug. 3. Remove the mudguard. 4. Disconnect the oxygen...

Transfer case (4WD) — installation
1. Install a new O-ring and pin into the transfer case. 2. Apply automatic transmission oil to the driven gear and the mounting surfaces of the transfer case and automatic transmission. Install the transfer case on the...

Automatic transmission assembly — removal
Attention: Install the jack and supports under the vehicle only in designated areas. For safety, place the removed wheel under the side sill behind the jack. Do not damage the paintwork of the fender guard. Remove the...

Automatic transmission assembly — installation
Caution: When connecting, do not mix up the tubes and electrical wiring. Do not touch the components and wiring in the installation area. 1. Install a new O-ring onto the torque converter and install it onto the...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Link in different formats to this section

TEXTHTMLBB Code