Six-cylinder car engines Honda Accord 6

General information about six-cylinder engines
This Part of the Chapter covers non-in situ repairs to the 3.0L V6 gasoline engine equipped with a fuel injection system. All procedures requiring removal of the powertrain are covered in the Engine Overhaul and Repair...

Preparatory actions and a list of repair procedures without removing the engine from the car
Clean the engine compartment and the outside surfaces of the power unit using one of a wide range of special solvents. This treatment will prevent dirt from getting inside the engine. If necessary, depending on the...

Bringing the piston of the first cylinder to the top dead center (TDC) position
Note. The following procedure is based on the assumption that the spark plug wires are connected correctly and the distributor is installed correctly. If it is necessary to bring the engine to TDC in order to adjust the...

Removal and installation cylinder head covers
Removal 1. Disconnect the negative cable from the battery. Warning! If the car stereo system is equipped with a security code, make sure you have the correct combination to activate the audio system before disconnecting...

Removal and installation the intake manifold
Attention! Proceed with the procedure only after the power unit has completely cooled down. Upper pipeline 1. Release the pressure in the fuel system (see Chapter Power and exhaust systems ). 2. Disconnect the negative...

Removal and installation of exhaust manifolds
Attention! Proceed with the procedure only after the power unit has completely cooled down. Removal 1. Disconnect the negative cable from the battery. Warning! If the car stereo system is equipped with a security code,...

Removal, condition check and installation of the timing belt and timing drive gears
Removal 1. Disconnect the negative cable from the battery. Warning! If the car stereo system is equipped with a security code, make sure you have the correct combination to activate the audio system before disconnecting...

Replacing the front crankshaft oil seal
1. Remove the timing belt and crankshaft sprocket (see Section Removal, condition check and installation of the timing belt and timing drive gears ). 2. Carefully pry the old seal out of its seat using a special tool or...

VTEC System — General Information
General information The VTEC system was developed by Honda specialists to provide dynamic control of valve timing and valve opening. Engines equipped with this system are marked with the VTEC inscription molded on the...

Removal, condition check and installation of rocker arm assembly
Removal 1. Remove the cylinder head cover (see Section Removal and installation cylinder head covers ). 2. Bring the piston of the first cylinder to the TDC position (see Section Bringing the piston of the first...

Removal, condition check and installation of camshafts
Removal 1. Remove the cylinder head covers (see Section Removal and installation cylinder head covers ), timing belt and gears (see Section Removal, condition check and installation of the timing belt and timing drive...

Replacing oil deflector caps and valve springs with plates
Note: Broken valve springs and worn valve stem seals can be replaced without removing the cylinder heads. All you need is two special tools and a source of compressed air. Before you begin, make sure you have a tool...

Removal and installation cylinder heads
Caution! Wait until the engine has completely cooled down before starting work. Removal 1. Disconnect the negative cable from the battery. Warning! If the car stereo system is equipped with a security code, make sure...

Removal and installation the engine oil pan
Removal 1. Disconnect the negative cable from the battery. Warning! If the car stereo system is equipped with a security code, make sure you have the correct combination to activate the audio system before disconnecting...

Removal, inspection and installation of the oil pump
Removal 1. Remove the timing belt, crankshaft sprocket and idler roller (see Section Removal, condition check and installation of the timing belt and timing drive gears ). Caution: Leave the powertrain mount support...

Removal and installation the drive disk
1. Remove the transmission (see Chapter Gear shift box ). Caution: The engine must be supported from above using a winch or A-beam. 2. Remove the bolts securing the drive disk to the crankshaft. 3. Carefully wipe the...

Replacing the rear crankshaft oil seal
1. Remove the transmission (see Chapter Gear shift box ) and the drive disk. Note: The engine should be supported from above using a winch or A-beam. 2. The oil seal can be replaced without first dismantling the oil pan...

Checking the condition and replacing the powertrain suspension supports
Examination 1. The suspension of the power unit on V6 models is carried out by means of four supports, the front and rear of which are equipped with hydraulic correctors, which make it possible to significantly reduce...

Powertrain suspension adjustment system
The front and rear suspension mounts of the power unit of models equipped with a V6 engine are equipped with hydraulic correctors, the operation of which is controlled by an on-board processor (PCM). The principle of...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Link in different formats to this section

TEXTHTMLBB Code