Electrical equipment of the car engine Honda Accord 6

Engine Electrical Specifications
Length of generator brushes, mm New brushes 10.41 Minimum acceptable value 1.52 Battery voltage, V With the engine off 11.5÷12 With the engine running 13.5÷15 Firing order 4-cylinder engines 1-3-4-2 V6 engines...

General information and precautions
Layout diagram of electrical components of a 4-cylinder engine in the engine compartment of a car 1 - Generator; 2 - High Voltage spark plug wires; 3 - Ignition distributor; 4 - Battery Schematic diagram of the...

Checking the battery status and replacing it
Caution! The negative cable should always be disconnected from the battery first and connected last! Examination 1. Disconnect both wires from the battery. Caution! The negative cable should always be disconnected first...

Checking the condition and replacing battery wires
1. Regularly inspect the battery cables along their entire length for signs of mechanical damage, cracks and burnt insulation, as well as traces of corrosion. Do not forget that a violation of the quality of the...

Ignition system — general information
Warning! High voltage is generated in the ignition system. Be careful and observe all necessary precautions when servicing any components of the system, including not only the main ones (ignition module, coil,...

Checking the functioning of the ignition system
Caution! Due to the very high voltage generated in the ignition system, its components must be serviced with extreme caution. This applies not only to the main components of the electronic ignition system, but also to...

Checking the condition and replacing the ignition coil
4-cylinder models Examination 1. Turn off the ignition (the key must be turned to the OFF position). 2. Remove the distributor cap, runner and protective screen. 3. Disconnect the electrical connectors of the ignition...

Checking the proper operation and replacing the ignition control module (ICM)
Examination 1. Check for proper power supply to the ignition module. Disconnect the wiring harness from the ICM. With the ignition on (without starting the engine), check for voltage at the following points: a) On V6...

Removal and installation the ignition distributor
Removal 1. Disconnect the negative cable from the battery. Warning! If the car stereo system is equipped with a security code, make sure you have the correct combination to activate the audio system before disconnecting...

Checking the ignition timing setting
Note: The procedure described below is intended only to check the basic settings made at the factory. No adjustments are possible, therefore, the only purpose of this test is to assess the correct operation of the...

Charging system — general information and precautions
The components of the charging system include the alternator, its built-in voltage regulator, charge indicator lamp, battery, protective fuse and wiring that connects these components. The charging system supplies...

Checking the status of the charging system
1. Remember that malfunctions of the charging system are not necessarily associated with generator failures. Always perform the following basic checks first: a) Check the condition of the battery wires where they are...

Removal and installation the generator
Removal 1. Disconnect the negative cable from the battery. Warning! If the car stereo system is equipped with a security code, make sure you have the correct combination to activate the audio system before disconnecting...

Replacing the voltage regulator and generator brushes
Note: This Section describes the procedure for measuring the brushes and voltage regulator on Nippondenso alternators installed on 4-cylinder models. The regulator on V6 models is replaced in conjunction with the...

Starting System — General Information and Precautions
The system ensures that the engine is turned over in order to start it. The main components of the system are the starter with a traction relay installed on it, the battery, the ignition switch and the connecting...

Checking the proper functioning of the starter on the vehicle (in situ)
Note: Before performing any starter function tests, make sure that the hard starting condition is not caused by a low battery level. If the starter does not turn at all when the ignition key is turned to the START...

Removal and installation the starter
1. Disconnect the negative cable from the battery. Warning! If the car stereo system is equipped with a security code, make sure you have the correct combination to activate the audio system before disconnecting the...

Removal and installation the traction relay
Note: On 4-cylinder models with manual transmission, a Nippondenso starter with a non-removable traction relay is used. If the latter fails, the entire assembly must be replaced. The description below applies to Mitsuba...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Link in different formats to this section

TEXTHTMLBB Code