Brake system of the car Honda Accord 6

Brake system specifications
Type Hydraulic, with vacuum booster Front brake mechanisms Disc, ventilated Rear brakes Disc or drum Parking brake With mechanical drive Foot brake pedal Free travel, mm 1.6÷4.8 Height, mm Models with manual...

Brake system — general information
All models of cars considered in this Manual are equipped with a hydraulic brake system with vacuum booster. Disc brakes are always installed on the front wheels, while the rear wheel mechanisms can have either a disc...

Anti-lock Brake System (ABS) — General Information and Error Codes
When a vehicle is equipped with a conventional braking system, abruptly pressing the foot brake pedal causes the wheels to lock. This disrupts the tread's grip on the road surface and the vehicle may skid, causing it to...

Replacement of brake pads of disc brake mechanisms
Warning! Brake pads must be replaced simultaneously on both front/rear brake mechanisms. Remember that dust generated during operation of the brake mechanisms may contain asbestos, which is extremely harmful to human...

Removal and installation of disc brake calipers
Warning! Remember that the dust generated during operation of the brake mechanisms may contain asbestos, which is extremely harmful to human health. Never blow off dust with compressed air or inhale it - wear a...

Checking the condition, removing and installing the brake disc
Note: The procedure applies equally to both front and rear disc brakes. Checking the status 1. Loosen the wheel nuts, jack up the car and support it. Remove the wheel in question, then screw the pair of wheel nuts back...

Replacing the shoes of the rear wheel drum brake mechanisms
Assembly of the drum brake mechanism of the right rear wheel 1 - Automatic regulator lever; 2 - Assembling the regulator; 3 - Wheel cylinder; 4 - Upper tension spring; 5 - Guide spring; 6 - Automatic regulator spring; 7...

Removal and installation wheel cylinders
Note: In case of leaks, wheel cylinders must be replaced without fail. Manufacturers do not recommend attempting to perform restorative repairs on these brake components. Removal 1. Jack up the rear of the car and place...

Removal and installation the master brake cylinder
Note: A failed brake master cylinder must be replaced. Manufacturers do not recommend attempting to perform a refurbishment of the brake master cylinder. Removal 1. The brake master cylinder is located in the engine...

Checking the condition and replacing brake lines and hoses
1. Approximately every six months, lift the car and check all flexible hoses connecting the steel tubes of the hydraulic circuits to the brake mechanisms of the wheels for cracks, signs of damage to the protective...

Bleeding the brake system
Warning! Bleed the brake system wearing protective glasses. If brake fluid accidentally gets into your eyes, rinse them immediately with plenty of water and seek medical help! 1. Bleeding the hydraulic system is...

Checking the serviceability and tightness, removing and installing the brake booster assembly
Checking the correct functioning 1. Without starting the engine, press the foot brake pedal several times. Make sure that there is no change in the amount of pedal reserve travel (the distance between the pedal and the...

Adjusting the parking brake
1. Remove the parking brake control lever trim (see Chapter Body ). 2. Remove the center console (see Chapter Body ). 3. Chock the front wheels, then jack up the rear of the car and place it on stands. Apply the parking...

Replacing the parking brake cables
1. Support the front wheels with wheel chocks, loosen the rear wheel nuts, then jack up the rear of the car and place it on supports. 2. On models equipped with rear drum brakes, remove the brake drum(s) (see Section...

Checking, replacing and adjusting the brake light switch sensor
Examination 1. Depress the foot brake pedal and check that the brake lights in the rear combination lamp assemblies operate properly. 2. If the brake lights do not work, check the condition of the corresponding fuse...

Checking and replacing the brake fluid level switch sensor
Examination 1. Disconnect the electrical connector of the sensor-switch and remove the cover from the master cylinder reservoir. 2. Check the free movement of the sensor float. If signs of jamming are detected, replace...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Link in different formats to this section

TEXTHTMLBB Code