Four-cylinder car engines Honda Accord 6

Engine specifications
Firing order 1-3-4-2 Cylinder numbering order 1-2-3-4 Direction of rotation of the crankshaft Counterclockwise Ø of cylinders, mm 86.11 Piston stroke, mm 97.03 Working volume, cm³ (l) 2261 (2.3) Maximum permissible...

General information about four-cylinder engines
This Part of the Chapter is devoted to non-in situ repairs of the 2.3L 4-cylinder petrol engine equipped with a fuel injection system. All procedures requiring removal of the powertrain are covered in Part General and...

Preparatory actions and repair procedures without removing the engine from the car
Clean the engine compartment and the outside surfaces of the power unit using one of a wide range of special solvents. This treatment will prevent dirt from getting inside the engine. If necessary, depending on the...

Bringing the piston of the first cylinder to the top dead center (TDC) position
Note: The following procedure is based on the assumption that the spark plug wires are connected correctly and the distributor is installed correctly. If it is necessary to bring the engine to TDC in order to adjust the...

Removal and installation the cylinder head cover
Removal 1. Disconnect the negative cable from the battery. Warning! If the car stereo system is equipped with a security code, make sure you have the correct combination to activate the audio system before disconnecting...

VTEC System — General Information and Component Health Check
General information The VTEC system was developed by Honda specialists to provide dynamic control of valve timing and valve opening. Engines equipped with this system are marked with the VTEC inscription molded on the...

Removal, condition check and installation of rocker arm assembly
Rocker Arm Assembly Components (VTEC Models) A - Fifth camshaft holder; B - Exhaust valve drive rocker arm (B); C - Spring of the exhaust valve rocker shaft; D - Secondary intake valve drive rocker arm; E - Intermediate...

Replacing oil deflector caps and valve springs with plates
Note: Broken valve springs and worn valve stem seals can be replaced without removing the cylinder head. All you need is two special tools and a source of compressed air. Before you begin, make sure you have a tool...

Removal and installation the intake manifold
Warning! Remember that gasoline is highly flammable! When servicing fuel system components, observe all applicable fire safety precautions. Do not smoke, do not approach work areas with open flames or unprotected...

Removal and installation the exhaust manifold
Removal 1. Disconnect the negative cable from the battery. Warning! If the car stereo system is equipped with a security code, make sure you have the correct combination to activate the audio system before disconnecting...

Removal, condition check and installation of gear wheels and balance shaft drive belt
Note. If the noise level increases due to the balance shaft drive belt, the first step is always to adjust its tension. This procedure can be done without removing the timing belt covers. The tension force of the belt...

Removal, condition check and installation of the timing belt and timing drive gears
Removal Note: If you hear any extraneous noises when the timing belt is operating, first check the adjustment of its tension. This procedure can be performed without removing the front covers (see paragraph 5 of Section...

Replacing the front crankshaft oil seal
1. Remove the drive belts (see Chapter Settings and ongoing maintenance ). 2. Remove the timing belt and balance shaft drive belt (see Sections Removal, condition check and installation of rocker arm assembly and...

Removal, condition check and installation of the camshaft
Removal and inspection 1. Remove the cylinder head cover (see Section Removal and installation cylinder head covers ). 2. Bring the piston of the first cylinder to the TDC position (see Section Bringing the piston of...

Removal and installation the cylinder head — removal and installation
Caution! Wait until the engine has completely cooled down before starting work. Removal 1. Bring the piston of the first cylinder to the TDC position of the end of the compression stroke (see Section Bringing the piston...

Removal and installation the engine oil pan
Removal 1. Warm up the engine to normal operating temperature, then drain the engine oil and remove the oil filter (see Chapter Settings and ongoing maintenance ). 2. Disconnect the negative cable from the battery....

Removal, inspection and installation of the oil pump
Removal 1. Remove the timing belt and balance shaft drive belt (see Sections Removal, condition check and installation of gear wheels and balance shaft drive belt and Removal, condition check and installation of the...

Removal and installation the flywheel/drive disc
Removal 1. Jack up the vehicle and place it on supports. Remove the gearbox (see Chapter Gear shift box ). 2. On models with manual transmission, remove the clutch assembly (see Chapter Clutch and drive shafts )....

Replacing the rear crankshaft oil seal
1. Remove the gearbox (see Chapter Gear shift box ). 2. Remove the flywheel/drive plate (see Section Removal and installation the flywheel/drive disc ). 3. Before removing the old seal, be sure to measure its seating...

Checking the condition and replacing the powertrain suspension supports
Note: Powertrain suspension mounts rarely require attention, but damaged mounts should be replaced without delay to avoid increased stress and premature wear of transmission line components. Examination 1. To check, it...

Powertrain suspension adjustment system
General information All models equipped with AT are equipped with an electronic control system for adjusting the parameters of the rear support of the power unit. The controlled parameter is the vibration level of the...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Link in different formats to this section

TEXTHTMLBB Code