Interior (internal body elements) of the car Honda Fit/Jazz 1

Removal and installation the interior rearview mirror
Note: Installation is carried out in the reverse order of removal. 1. Disconnect the clamps (A) and carefully remove the cover (B). 2. Loosen the screws (A), detach the holder (B) and remove the interior mirror (C).

Instrument cluster panel trim
Note: Assemble in the reverse order of disassembly. Before carrying out work, read the chapter " Supplementary Restraint System (SRS) ". After assembly, check the airbags. After assembly, make sure the steering wheel...

Thermal insulator — disassembly and assembly
1. Remove the heat insulator (A) as shown in the figure. 2. Loosen the bolts (B and C), disconnect the fasteners (E) and clamps (F), and remove the trim (D) of the heat insulator.

Bottom panel — disassembly and assembly
(Driver's side) 1. Turn the handle (B) 90°. 2. Gently pull up on the left (right hand drive models) or right side lower panel (A) and release the clip (D). 3. Pull the bottom panel towards you, release the clips (C) and...

Ashtray (left-hand drive models) — disassembly and assembly
1. Turn the handle (A) 90°. 2. Pull the ashtray (A) by the top edge, release the clips, clamps (B) and remove the ashtray. 3. If necessary, loosen the screws and separate the container (A) from the ashtray (B).

Central instrument panel trim
1. Remove the glove box and lower panel on the passenger side. 2. Loosen the screw (A), release the clips (B) and clamps (C), and remove the lower center trim cover. 3. (Except for right-hand drive model with CVT)...

Glove box — disassembly and assembly
1. Loosen the bolts (A). Tightening torque - 5 Nm Left-hand drive models. Right hand drive models. 2. Disconnect the stoppers (B) and then remove the glove box (A). Left-hand drive models. Right hand drive models. 3....

Central deflector grille
1. Using a screwdriver, release the clips (B) and lift the deflector grille (A). Note: Before use, wrap the screwdriver with protective tape. To avoid damaging the deflector grille and instrument panel, stick adhesive...

Central deflector — disassembly and assembly
1. Remove the air ducts. 2. Loosen the screws and then remove the center deflector (A).

Left panel on the passenger side
1. Remove the side rear view mirror drive switch (A). 2. Using a screwdriver, disconnect the clips (B and D), and then remove the coin box (C) as shown in the figure above. Note: Please wrap the screwdriver with...

Central bracket — disassembly and assembly
1. Hold the glove box and release its stoppers. 2. Loosen the screws and then remove the center bracket (A).

External deflector — disassembly and assembly
1. Remove the air ducts. 2. Loosen the screws (A and B) and then remove the outer deflector (C).

Air duct — disassembly and assembly
(Driver's side) Loosen the screws (A), release the clips (B), and then remove the air duct (C). (Passenger side) 1. Remove the center console. 2. Disconnect the clip and then disconnect the air duct (A) from the...

Trim for manual transmission lever or automatic transmission selector
1. Release the stoppers and lower the glove box down. 2. (Models with left-hand drive and manual transmission) Remove the gear shift knob. 3. Bend back the holder (B) and disconnect the connector (C). 4. Disconnect the...

Center console — disassembly and assembly
1. Disconnect the clamps and remove the parking brake cover (A). 2. (Models with left-hand drive and manual transmission) Remove the gear shift knob. 3. When removing the center console, refer to the assembly drawing...

Interior trim — removal and installation
1. When removing the interior trim, refer to the assembly drawing "Interior trim". 2. Installation is carried out in the reverse order of removal. Interior trim. 1 - front pillar trim, 2 - front door seal, 3 - upper...

Removal and installation the spare wheel compartment cover
1. When removing the side cover, refer to the assembly drawing "Spare wheel compartment cover". Spare wheel compartment cover. 1 - spare wheel compartment cover, 2 - side bushing, 3 - fasteners, 4 - rear door interior...

Removal and installation the side trim of the luggage compartment
1. When removing the side trim of the luggage compartment, refer to the assembly drawing "Side trim of the luggage compartment". Side trim of the luggage compartment. 1 - rear side door seal, 2 - lower rear seat belt...

Removal and installation rear pillar trim
1. Remove the luggage compartment side trim. 2. When removing the rear pillar trim, refer to the assembly drawing "Rear Pillar Trim". Rear pillar trim. 1 - upper rear seat belt mount, 2 - right rear pillar trim, 3 -...

Roof Finishing — Removal and Installation
Note: When removing the roof trim, refer to the assembly drawing "Roof Trim". Installation is carried out in the reverse order of removal. 1. Remove the front pillar trims (see section " Interior trim "). 2. Remove the...

Removal and installation roof trim strips
1. Remove the roof trim. 2. Disconnect the clips (A), then remove the front (B) and rear (C) trims. 3. Installation is carried out in the reverse order of removal. Front overlay. Back cover.

Removal and installation the luggage compartment mat
Note: Installation is carried out in the reverse order of removal. 1. Fold the rear seats. 2. Disconnect the clips (C) and remove the child restraints (A) from the luggage compartment carpet (B). 3. Remove the pins and...

Removal and installation front seat belts
Caution: Do not disassemble the seat belt pretensioner. Note: Check the seat belts after installation (see relevant subsection). Warning: If the front seat belts are not used correctly, the seat belt pretensioner may...

Front seat belt buckles
1. Remove the front seat (see section " Removal and installation seats "). 2. Remove the seat side trim (see section " Removal and installation seats "). 3. Disconnect the clips (B) and connector (A) from the driver's...

Rear seat belts
1. Remove the rear seat belt lower mounting bolt (A). Tightening torque - 32 Nm 2. Remove the side trim of the luggage compartment (see section " Interior trim "). 3. Remove the cover (A) of the seat belt upper anchor...

Rear seat belt buckles and center seat belt
1. Disconnect the clips (B), then pull the interior carpet (A) from under the rear seat (C) towards you. 2. Remove the lock straps (F) from the base (D) of the mat through the opening (E). 3. Loosen the bolts (A) and...

Checking the seat belt
1. Make sure the seat belt is installed correctly. 2. Check the seat belt for damage and deformation of metal parts. If there is damage, the belt must be replaced. 3. Make sure the seat belt can be pulled out freely. 4....

Removal and installation front seats
Note: Installation is carried out in the reverse order of removal. Note: Before carrying out work, read the chapter " Supplementary Restraint System (SRS) ". 1. Disconnect the cable from the negative battery terminal...

Removal and installation rear seats
1. Disconnect the clips (B), then pull the interior carpet (A) from under the rear seat (C) towards you. 2. Fold down the rear seats (C), release the clips (B) and fold the front end of the spare wheel compartment cover...

Removal and installation the rear seat guide
1. Loosen the screws (A), disconnect the clamps (C) and remove the guide cover (B). 2. Loosen the bolt (A), then remove the guide (B). Tightening torque - 22 Nm

Removal and installation the rear seat cushion retainer
1. Loosen the screw (A) and remove the cover (B) of the retainer. 2. Loosen the screws (A), disconnect the pins (B), and remove the cover (C) of the rear seat bracket hole. 3. Remove the bolts (A), disconnect the rod...

Removal and installation the rear seat bracket
1. Remove the side trim of the luggage compartment (see section " Interior trim "). 2. Loosen the bolts (A), then remove the bracket (B). Tightening torque - 22 Nm

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Link in different formats to this section

TEXTHTMLBB Code