HondaBook.ru
Auto companies Volkswagen Auto companies Ford Auto companies Lada Auto companies Skoda Auto companies BMW Auto companies Mazda Auto companies Peugeot
English Русский
Български
Беларускі
Український
Српски
Hrvatski
Română
Polski
Slovenský
Magyar
Bookmark Contacts Sitemap   
 
 
 
 
 
 
 
Accord Civic Fit / Jazz CR-V HR-V Others Articles
CR-V 1 (1995-2001, petrol) CR-V 2 (2002-2006, petrol)

Springs — removal and installation (Honda CR-V 1)

  • Main
  • Honda CR-V
  • 1 (1995-2001, petrol)
  • Chassis and running gear
  • Rear suspension
  • Springs — removal and installation
0
Contents: CR-V Cars ⇊ 4-cylinder Odyssey ⇊ Odyssey V6 ⇊

CR-V Cars



1. Raise the vehicle.

2. Remove the rear wheels.

3. Remove the stand (see below).

4. Place the stand in a vice and compress the spring with a compressor.

5. Unscrew the self-locking nut.

6. Remove the washer, rubber bushings and spring gasket.

7. Remove the spring.

8. Installation is carried out in reverse order.

4-cylinder Odyssey



Removal



1. Raise the vehicle.

3. Place a jack under the spring rest and lift the lower arm.

4. Unscrew the bolts securing the shock absorber and knuckle on the lower arm.

5. Compress and remove the shock absorber (see below).

6. Lower the lower arm, releasing the spring.

7. Remove the spring assembly and support cups.

Installation



8. Check the upper and lower support cups for damage. Replace damaged cups.

9. Install the support cups.

10. Install the spring. Align the edge of the spring with the recess in the spring cup.

11. Raise the lever and compress the spring.

12. Screw in the shock absorber and steering knuckle mounting bolts.

13. Place the jack under the steering knuckle. Raise your fist so that it supports the weight of the car. Tighten the two mounting bolts to 103 Nm. Tighten the shock absorber mounting nut to 38 Nm.

14. Lower the vehicle. Check and adjust the rear wheel alignment.

Odyssey V6



Removal



1. Raise the vehicle.

2. Remove the wheel.

3. Place a jack under the lower arm and lift the arm.

4. Loosen the speed sensor bracket mounting bolts and disconnect the wiring from the lower arm. Do not disconnect the wiring from the sensor.



5. Unscrew the bolt securing the lower arm to the knuckle.

6. Remove the spring by gradually lowering the jack.

Installation



7. Install the spring. Align the edge of the spring with the recess on the spring cup.

8. Jack up the lower arm, align the holes and tighten the bolts.

9. Attach the speed sensor bracket and wiring.

10. Raise the lower arm with a jack so that the jack supports the weight of the car. Tighten the bolts to 74 Nm.

11. Lower the vehicle. Check and adjust rear wheel alignment.

(The text can be found on the website: hondabook.ru)
This article is available at: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
This information has been verified: Emil Safonov
Share with friends:
◀ Previous
CR-V 1: Rear suspension
Next ▶

Rear suspension — design description
Rear suspension parts
Shock absorbers — removal and installation
Rack (CR-V) — Removal and Installation
Rear suspension arms — removal and installation
Anti-roll bar — removal and installation
Rear Hub and Bearings (CR-V)
See also other articles from Honda manuals:
Valve springs and valve stem seals Honda Accord 3 (1985-1989)
Valve springs, plates and seals — replacement Honda Civic 3 and 4 (1983-1991)
Valves, springs and seals — removal Honda HR-V 1 (1998-2006, petrol)
Link in different formats to this article
Comments and feedback from visitors
No comments yet


How much will 30 + 25 ?

       



CR-V 2 (2002-2006, petrol) 
  • General information
  • User manual
  • Technical data
  • Maintenance
  • Power unit
  • Engine repair
  • Lubrication system
  • Cooling system
  • Exhaust system
  • Fuel system
  • Engine management
  • Engine electrical equipment
  • Transmission
  • Clutch
  • Manual gearbox
  • Automatic gearbox
  • Rear differential
  • Drive shafts
  • Chassis and running gear
  • Steering
  • Front suspension
  • Rear suspension
  • Brake system
  • Body and interior
  • Exterior (external elements)
  • Interior (internal elements)
  • Doors, locks and windows
CR-V 1 (1995-2001, petrol) 
  • General information
  • Maintenance
  • Tips for car owner
  • Power unit
  • Engine repair
  • Engine overhaul
  • Cooling and lubrication system
  • Engine electrical equipment
  • Control system
  • Fuel system
  • Transmission
  • Clutch and drive shafts
  • Car gearbox
  • Chassis and running gear
  • Front suspension
  • Rear suspension
  • Steering
  • Brake system
  • Body and interior
  • Body service
  • Exterior (external elements)
  • Interior (internal elements)
  • Electrical equipment
  • Equipment and devices
  • Electrical circuits
HondaBook.ru © 2018–2026 • Mobile version • Sitemap: EN BG BY UA RS HR RO PL SK HU • Feedback • Driver Information • Search system • Bookmark
Accord 3 (1985-1989) • Accord 6 (1997-2002) • Civic 3 and 4 (1983-1991) • Civic 5 and 6 (1991-2000) • Civic 6 (1995-2000) • Civic 7 (2000-2005) • Civic 8 (2005-2011) • Fit 1 (2001-2008) • CR-V 1 (1995-2001) • CR-V 2 (2002-2006) • HR-V 1 (1998-2006) • Avancier 1 (1999-2003) •
 
This website uses cookies to ensure proper functioning. By clicking "OK," you agree.