Doors, locks and windows of the car Honda HR-V 1
Location of door and window components
1. DOOR SEALING 2. CENTRAL GUIDE FILM. Replacement ( see below ) 3. UPPER GUIDE FILM. Replacement ( see below ) 4. DOOR MOLDING 5. DOOR. Replacement ( see below ) 6. LOOP 7. FIXATOR 8. FLAP POCKET BRACKET 9. INTERNAL...
1. DOOR SEALING 2. CENTRAL GUIDE FILM. Replacement ( see below ) 3. UPPER GUIDE FILM. Replacement ( see below ) 4. DOOR MOLDING 5. DOOR. Replacement ( see below ) 6. LOOP 7. FIXATOR 8. FLAP POCKET BRACKET 9. INTERNAL...
Removal and installation the door panel
1. Remove the inner handle housing. Be careful not to scratch the door panel. 2. Remove the fold-down pocket panel, then disconnect the power window switch connector and the power mirror switch connector. 3. Remove the...
1. Remove the inner handle housing. Be careful not to scratch the door panel. 2. Remove the fold-down pocket panel, then disconnect the power window switch connector and the power mirror switch connector. 3. Remove the...
Replacing the outside door handle
Note: Wear protective gloves when removing and installing the outer handle. 1. Raise the glass fully. 2. Remove: Door panel ( see above ) Plastic lid (if necessary) 3. Remove the screws from the lock. 4. Disconnect the...
Note: Wear protective gloves when removing and installing the outer handle. 1. Raise the glass fully. 2. Remove: Door panel ( see above ) Plastic lid (if necessary) 3. Remove the screws from the lock. 4. Disconnect the...
Replacing a door lock
Note: When replacing the door lock, wear protective gloves. 1. Raise the glass fully. 2. Remove the outer handle ( see above ). 3. If necessary, remove the glass guide channel from the center lower guide. Loosen the...
Note: When replacing the door lock, wear protective gloves. 1. Raise the glass fully. 2. Remove the outer handle ( see above ). 3. If necessary, remove the glass guide channel from the center lower guide. Loosen the...
Replacing door glass and window lifter
Note: Wear protective gloves when removing and installing the glass and window regulator. 1. Remove: Door panel ( see above ) Plastic lid 2. Carefully lift the glass until you see the bolts. Loosen them. Slide the guide...
Note: Wear protective gloves when removing and installing the glass and window regulator. 1. Remove: Door panel ( see above ) Plastic lid 2. Carefully lift the glass until you see the bolts. Loosen them. Slide the guide...
Replacing the waterproof film in the door guides
Note: Prevent dust from entering the work area. When working at low temperatures, warm up the door guide and film with a hair dryer. Door guide: about 15°C. Door guide film: about 30°C. When heating the door guide film,...
Note: Prevent dust from entering the work area. When working at low temperatures, warm up the door guide and film with a hair dryer. Door guide: about 15°C. Door guide film: about 30°C. When heating the door guide film,...
Adjusting the door position
Note: After installing the door, make sure it is flush with the body, then make sure the gaps between the front, rear and bottom edges of the door and the body are the same. Make sure the edges of the door and the body...
Note: After installing the door, make sure it is flush with the body, then make sure the gaps between the front, rear and bottom edges of the door and the body are the same. Make sure the edges of the door and the body...
Rear view mirror component locations
1. electric mirror replacement ( see below ); 2. mirror support cover; 3. mirror; 4. Mirror holder. Replacement (see below). Without roof spoiler. With roof spoiler 1. mirror holder; 2. base of the rack; 3. lock bolt;...
1. electric mirror replacement ( see below ); 2. mirror support cover; 3. mirror; 4. Mirror holder. Replacement (see below). Without roof spoiler. With roof spoiler 1. mirror holder; 2. base of the rack; 3. lock bolt;...
Replacing the rear view mirror
1. Lower the mirror completely. 2. Remove: Door panel ( see above ). Plastic lid. 3. Carefully pry up the mirror support cover with your hand. Power Mirror: Remove the cover, loosen the screw and remove the handle, then...
1. Lower the mirror completely. 2. Remove: Door panel ( see above ). Plastic lid. 3. Carefully pry up the mirror support cover with your hand. Power Mirror: Remove the cover, loosen the screw and remove the handle, then...
Replacing the rear view mirror holder
Note: Don't scratch the mirror. When removing and installing the mirror holder, wear protective gloves. 1. Gently pull the lower edge of the mirror holder by hand. If necessary, disconnect the heater connector. 1....
Note: Don't scratch the mirror. When removing and installing the mirror holder, wear protective gloves. 1. Gently pull the lower edge of the mirror holder by hand. If necessary, disconnect the heater connector. 1....
Windshield replacement
Note: Wear protective gloves when removing and installing the windshield. To avoid damaging the finish, use seat covers. Use glass bonding kit, P/N 08C73-X0230N. 1. Remove: Rear view mirror (with rear spoiler, see above...
Note: Wear protective gloves when removing and installing the windshield. To avoid damaging the finish, use seat covers. Use glass bonding kit, P/N 08C73-X0230N. 1. Remove: Rear view mirror (with rear spoiler, see above...
Locations of body glazing components
The numbers after the component names indicate the quantity of components used. 1. WINDSHIELD MOLDING 2. UPPER MOLDING SEAL, 2 3. UPPER RUBBER GASKET 4. SIDE MOLDING SEAL, 2 5. FASTENING, 2 (self-adhesive, from the body...
The numbers after the component names indicate the quantity of components used. 1. WINDSHIELD MOLDING 2. UPPER MOLDING SEAL, 2 3. UPPER RUBBER GASKET 4. SIDE MOLDING SEAL, 2 5. FASTENING, 2 (self-adhesive, from the body...
Roof hatch — design description
1. glass seal; 2. rubber; 3. glass holder; 4. glass; 5. clamp; 6. rear drain pipe; 7. rear drain valve; 8. lens hood stopper; 9. washer; 10. E-clamp; 11. lock cover; 12. lock assembly; 13. Loop socket; 14. limiter; 15....
1. glass seal; 2. rubber; 3. glass holder; 4. glass; 5. clamp; 6. rear drain pipe; 7. rear drain valve; 8. lens hood stopper; 9. washer; 10. E-clamp; 11. lock cover; 12. lock assembly; 13. Loop socket; 14. limiter; 15....
Replacing glass in the sunroof
1. Remove the sunshade. 2. Loosen the screw, then remove the lock cover. 3. Remove the roof trim. 4. Remove the bolts from the lock assembly, then remove the nuts. 5. The glass is removed by pressing upwards. 6....
1. Remove the sunshade. 2. Loosen the screw, then remove the lock cover. 3. Remove the roof trim. 4. Remove the bolts from the lock assembly, then remove the nuts. 5. The glass is removed by pressing upwards. 6....
Replacing the main hatch seal
1. Remove the glass ( see above ). 2. Remove the main seal from the body. 3. Clean the contact surface on the body with a sponge soaked in alcohol. After cleaning, do not allow oil, grease or water to get on the body...
1. Remove the glass ( see above ). 2. Remove the main seal from the body. 3. Clean the contact surface on the body with a sponge soaked in alcohol. After cleaning, do not allow oil, grease or water to get on the body...
Replacing the drain pipe
1. clamp; 2. front drain pipe; 3. Front drain valve; 4. rear drain valve; 5. rear drain pipe; 6. roof panel stiffener 1. Remove: Ceiling lining ( see below ). Rear side trim ( see below ). Wheel arch panel. Fuse box...
1. clamp; 2. front drain pipe; 3. Front drain valve; 4. rear drain valve; 5. rear drain pipe; 6. roof panel stiffener 1. Remove: Ceiling lining ( see below ). Rear side trim ( see below ). Wheel arch panel. Fuse box...
Replacing the hatch lock assembly and hinges
1. hinge socket; 2. loop sleeve; 3. loop; 4. glass holder; 5. glass; 6. rubber; 7. lock assembly
1. hinge socket; 2. loop sleeve; 3. loop; 4. glass holder; 5. glass; 6. rubber; 7. lock assembly
Rear door — removal and installation
1. Rear license plate light connector; 2. Rear door lock actuator connector; 3. harness clamp; 4. harness clamps; 5. Rear window heater connector; 6. tourniquet; 7. rubber bushing; 8. Rear window wiper motor connector;...
1. Rear license plate light connector; 2. Rear door lock actuator connector; 3. harness clamp; 4. harness clamps; 5. Rear window heater connector; 6. tourniquet; 7. rubber bushing; 8. Rear window wiper motor connector;...
Rear door — adjustment
Note: Before you begin adjusting the rear door, loosen the bolts and nuts slightly. The support posts must be removed. 1. Adjust the rear door hinges on the right and left, as well as on the front and rear using the...
Note: Before you begin adjusting the rear door, loosen the bolts and nuts slightly. The support posts must be removed. 1. Adjust the rear door hinges on the right and left, as well as on the front and rear using the...
Replacing the rear door support pillar
Note: When removing the rear door, it is a good idea to have an assistant. Avoid scratching the rear door and interior trim. 1. Loosen the nut, then remove the support post from the bracket. 2. Remove the support pillar...
Note: When removing the rear door, it is a good idea to have an assistant. Avoid scratching the rear door and interior trim. 1. Loosen the nut, then remove the support post from the bracket. 2. Remove the support pillar...
Installing the rear door seal
1. Locate the alignment mark painted on the rear door seal. Align the mark with the center of the rear door. Make sure there are no folds in the seal. 1. rear door seal; 2. alignment mark; 3. from the inside; 4. body;...
1. Locate the alignment mark painted on the rear door seal. Align the mark with the center of the rear door. Make sure there are no folds in the seal. 1. rear door seal; 2. alignment mark; 3. from the inside; 4. body;...
Opening devices — arrangement of components
1. rear door lock cylinder; 2. rear door handle; 3. Rear door opening cable; 4. Fuel tank filler door latch; 5. rear door lock; 6. Fuel tank filler door opening lever, replacement; 7. hood release cable; 8. hood latch
1. rear door lock cylinder; 2. rear door handle; 3. Rear door opening cable; 4. Fuel tank filler door latch; 5. rear door lock; 6. Fuel tank filler door opening lever, replacement; 7. hood release cable; 8. hood latch
Hood lock cable
Note: Avoid scratching the body and adjacent components. 1. Remove: Radiator grille ( see above ). Inner wing. Wing panel. 2. Disconnect the hood release cable from the hood latch ( see below ). 3. Using a clamp...
Note: Avoid scratching the body and adjacent components. 1. Remove: Radiator grille ( see above ). Inner wing. Wing panel. 2. Disconnect the hood release cable from the hood latch ( see below ). 3. Using a clamp...
Replacing the fuel filler door opening cable
Note: Avoid scratching the body and adjacent components. 1. Remove: Side trim ( see above ). The back of the rear seat ( see above ). Rear seat cushion ( see above ). Rear trim ( see above ). If necessary, carpet ( see...
Note: Avoid scratching the body and adjacent components. 1. Remove: Side trim ( see above ). The back of the rear seat ( see above ). Rear seat cushion ( see above ). Rear trim ( see above ). If necessary, carpet ( see...
Replacing the hood release handle
Note: Avoid scratching the body and adjacent components. 1. Remove the wing panel. 2. Loosen the bolts, then remove the hood release handle. 1. Hood release handle 3. Installation is performed in the reverse order of...
Note: Avoid scratching the body and adjacent components. 1. Remove the wing panel. 2. Loosen the bolts, then remove the hood release handle. 1. Hood release handle 3. Installation is performed in the reverse order of...
Replacing the hood latch
Note: Avoid scratching the body and adjacent components. 1. Remove the front bumper ( see above ). 2. Remove the bolts, then remove the hood latch. Disconnect the hood release cable from the hood latch. 3. Installation...
Note: Avoid scratching the body and adjacent components. 1. Remove the front bumper ( see above ). 2. Remove the bolts, then remove the hood latch. Disconnect the hood release cable from the hood latch. 3. Installation...
Replacing the fuel filler door opening lever
Note: Avoid scratching the body and adjacent components. 1. Remove: Side trim ( see above ). Carpeting (if required) ( see above ). 2. Remove the bolts, then remove the fuel filler door release lever. Disconnect the...
Note: Avoid scratching the body and adjacent components. 1. Remove: Side trim ( see above ). Carpeting (if required) ( see above ). 2. Remove the bolts, then remove the fuel filler door release lever. Disconnect the...
Replacing the fuel filler door latch
Note: Avoid scratching the body and adjacent components. 1. Remove the left side trim ( see above ). 2. Turn the door latch 90' and remove it. 3. Installation is carried out in the reverse order of removal, taking into...
Note: Avoid scratching the body and adjacent components. 1. Remove the left side trim ( see above ). 2. Turn the door latch 90' and remove it. 3. Installation is carried out in the reverse order of removal, taking into...
Replacing the rear door handle
Note: Avoid scratching the body and adjacent components. 1. Remove the rear license plate plate ( see above ). 2. Disconnect the rear door release cable from the rear door handle. 3. Unscrew the nuts, then remove the...
Note: Avoid scratching the body and adjacent components. 1. Remove the rear license plate plate ( see above ). 2. Disconnect the rear door release cable from the rear door handle. 3. Unscrew the nuts, then remove the...
Replacing the rear door lock
Note: Avoid scratching the body and adjacent components. 1. Remove the trim from the rear door ( see above ). 2. Disconnect the rear door lock switch connector and rear door lock actuator connector, then disconnect the...
Note: Avoid scratching the body and adjacent components. 1. Remove the trim from the rear door ( see above ). 2. Disconnect the rear door lock switch connector and rear door lock actuator connector, then disconnect the...
Replacing the rear door lock cylinder
Note: Avoid scratching the body and adjacent components. 1. Remove the trim from the rear door ( see above ). 2. Disconnect the cylinder rod, then unscrew the bolt. 3. Turn the rear door lock cylinder and remove it. 4....
Note: Avoid scratching the body and adjacent components. 1. Remove the trim from the rear door ( see above ). 2. Disconnect the cylinder rod, then unscrew the bolt. 3. Turn the rear door lock cylinder and remove it. 4....
This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Link in different formats to this section
TEXTHTMLBB Code
- General information
- User manual
- Maintenance
- Power unit
- Engine repair
- Lubrication system
- Cooling system
- Fuel injection and control
- Power and exhaust system
- Engine electrical equipment
- Transmission
- Clutch
- Mechanical gearbox
- Automatic gearbox
- Rear differential
- Drive shafts and cardan
- Chassis and running gear
- Steering
- Car suspension
- Brake system
- Body and interior
- Exterior (external elements)
- Interior (internal elements)
- Doors, locks and windows
- Electrical equipment
- Equipment and devices
- Lighting system
- Electrical circuits