Car engine lubrication system Honda HR-V 1
Engine lubrication system — design description
Models for Europe, Australia and South Africa 1. OIL PUMP. Repair ( see below ). Examination ( see below ). Apply sealant to the contact surface of the block. 2. REFERENCE PIN 3. O-RING, Replace. 4. OIL PRESSURE SENSOR,...
Models for Europe, Australia and South Africa 1. OIL PUMP. Repair ( see below ). Examination ( see below ). Apply sealant to the contact surface of the block. 2. REFERENCE PIN 3. O-RING, Replace. 4. OIL PRESSURE SENSOR,...
Engine oil — check
1. Park the car on a level surface and turn off the engine. Wait a few minutes and allow the oil to drain back into the oil pan until the indicator shows the actual level. 2. Make sure that the oil level on the gauge is...
1. Park the car on a level surface and turn off the engine. Wait a few minutes and allow the oil to drain back into the oil pan until the indicator shows the actual level. 2. Make sure that the oil level on the gauge is...
Engine oil — replacement
1. Warm up the engine. 2. Drain the engine oil. 3. Replace the drain plug with a new washer and fill with the recommended oil. Oil requirements Always use fuel economy oil that has "API Service SG, SH or SJ" written on...
1. Warm up the engine. 2. Drain the engine oil. 3. Replace the drain plug with a new washer and fill with the recommended oil. Oil requirements Always use fuel economy oil that has "API Service SG, SH or SJ" written on...
Oil filter — replacement
1. Unscrew the oil filter with a special key. 2. Check the condition of the threads and rubber seal on the new filter. Wipe the seat on the cylinder block, then apply a thin layer of oil to the rubber seal of the...
1. Unscrew the oil filter with a special key. 2. Check the condition of the threads and rubber seal on the new filter. Wipe the seat on the cylinder block, then apply a thin layer of oil to the rubber seal of the...
Oil Pressure Sensor — Testing
1. Disconnect the YELLOW/RED wire from the engine oil pressure sensor. 2. Check if there is continuity between the positive terminal and the motor (ground). When the engine is not running, there should be conductivity....
1. Disconnect the YELLOW/RED wire from the engine oil pressure sensor. 2. Check if there is continuity between the positive terminal and the motor (ground). When the engine is not running, there should be conductivity....
Oil pressure — testing
If the oil pressure warning light stays on while the engine is running, check the engine oil level. If the level is normal: 1. Connect the tachometer. 2. Unscrew the oil pressure sensor and install an oil pressure gauge...
If the oil pressure warning light stays on while the engine is running, check the engine oil level. If the level is normal: 1. Connect the tachometer. 2. Unscrew the oil pressure sensor and install an oil pressure gauge...
Oil pump — design description
1. PUMP HOUSING. Checking ( see below ) When installing, apply sealant to the contact surface of the cylinder block. 2. REFERENCE PIN 3. INTERNAL GEAR. Check ( see below ) 4. OUTER GEAR. Check ( see below ) 5. 6x1.0 mm,...
1. PUMP HOUSING. Checking ( see below ) When installing, apply sealant to the contact surface of the cylinder block. 2. REFERENCE PIN 3. INTERNAL GEAR. Check ( see below ) 4. OUTER GEAR. Check ( see below ) 5. 6x1.0 mm,...
Oil pump — removal, inspection and installation
1. Drain the engine oil. 2. Turn the crankshaft and align the white notch on the crankshaft pulley with the arrow on the lower cover. 3. Remove the cylinder head cover and top cover. 4. Remove the power steering pump,...
1. Drain the engine oil. 2. Turn the crankshaft and align the white notch on the crankshaft pulley with the arrow on the lower cover. 3. Remove the cylinder head cover and top cover. 4. Remove the power steering pump,...
This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Link in different formats to this section
TEXTHTMLBB Code
- General information
- User manual
- Maintenance
- Power unit
- Engine repair
- Lubrication system
- Cooling system
- Fuel injection and control
- Power and exhaust system
- Engine electrical equipment
- Transmission
- Clutch
- Mechanical gearbox
- Automatic gearbox
- Rear differential
- Drive shafts and cardan
- Chassis and running gear
- Steering
- Car suspension
- Brake system
- Body and interior
- Exterior (external elements)
- Interior (internal elements)
- Doors, locks and windows
- Electrical equipment
- Equipment and devices
- Lighting system
- Electrical circuits