Interior (internal body elements) of the car Honda HR-V 1

Replacing the interior rearview mirror
1. Remove the rack cover. 2. Remove the mirror holder. 3. Loosen the screws, then remove the rearview mirror. 4. Installation is carried out in the reverse order of removal. With a spoiler on the roof 1. Remove the rack...

Interior trim — design description
Supplemental Restraint System (SRS) components are located in areas marked with an asterisk (*). Review SRS component locations, precautions, and procedures before performing repairs or maintenance. 1. side cover...

Removal and installation of interior trim
1. rear pillar trim; 2. hook; 3. rear side shelf; 4. Front seat belt upper anchor bolt, 7/16-20 UNF, 32 Nm (3.3 kgf/m); 5. B-pillar trim; 6. door finishing; 7. hooks; 8. Front pillar trim; 9. left wheel arch panel; 10....

Replacing carpet
1. foot support; 2. fasteners; 3. retainer; 4. carpet This area contains the Supplemental Restraint System (SRS) components. Review the SRS component locations, precautions, and procedures before performing repairs or...

Removal and installation the front and rear console
Note: When pressing components with a flat-head screwdriver, wrap it with protective tape to avoid damage. Avoid scratching the front seat, instrument panel and adjacent components. Do not bend the parking brake cables....

Removal and installation the instrument cluster
Note: When pressing components with a flat-head screwdriver, wrap it with protective tape to prevent damage and apply tape to adjacent components. Avoid scratching the instrument panel and adjacent components. 1. Tilt...

Removal and installation the central section of the instrument panel
Note: When pressing components with a flat-head screwdriver, wrap it with protective tape to prevent damage and apply tape to adjacent components. Avoid scratching the instrument panel and adjacent components. 1. Remove...

Removal and installation the glove box
Note: Avoid scratching the instrument panel and adjacent components. 1. Loosen the bolts, then remove the glove box. 2. Installation is performed in the reverse order of removal.

Removal and installation the top drawer cover
Note: Avoid scratching the instrument panel and adjacent components. 1. Loosen the bolts, then remove the top drawer cover. 2. Installation is performed in the reverse order of removal.

Removal and installation the pocket on the driver's side
Note: Avoid scratching the instrument panel and adjacent components. 1. Unscrew the bolts. 2. Remove the clip and unhook the hooks, then remove the pocket from the driver's side. 3. Installation is performed in the...

Removal and installation the upper pocket on the driver's side
Note: Avoid scratching the instrument panel and adjacent components. 1. Unhook the hooks. 2. Remove the clips, then remove the upper pocket from the driver's side. 3. Installation is performed in the reverse order of...

Removal and installation the instrument panel
1. heater control panel; 2. heater; 3. instrument panel; 4. Cup holder lighting connector; 5. Connector of intermediate instrument harness This area contains the Supplemental Restraint System (SRS) components. Review...

Replacing the steering bracket beam
1. inertia switch; 2. steering bracket beam; 3. ground bolt, 6x10 mm, 9.8 Nm (1.0 kgf/m); 4. 6x10 mm, 9.8 Nm (1.0 kgf/m); 5. main harness; 6. SRS harness; 7. interior harness This area contains the Supplemental...

Seats — Component Locations
1. REAR SEAT - Removal and installation ( see below ) - Removing and installing the backrest latch ( see below ) - Replacement of the back cover ( see below ) - Replacing the seat cushion cover ( see below ) 2. FRONT...

Seats — removal and installation
1. Remove the end caps from the seat guides and unscrew the bolts securing the front seat. When pressing the components with a flat-head screwdriver, wrap it with protective tape to avoid damage and stick the tape on...

Disassembling and assembling the front seat
Driver's seat Note: Avoid scratching the body or tearing the seat covers. When pressing components with a flat-head screwdriver, wrap it with protective tape to avoid damage. 1. HEADREST 2. Forward 3. HOOK 4. SEAT...

Replacing the front seat cover
Note: Do not tear the seams or damage the seat covers. Wear protective gloves. Backrest cover 1. Fold the backrest forward. 2. Unhook the hook. 3. Fold back the back cover, then unhook all the internal springs. 4....

Removal and installation the rear seat
Note: Do not scratch the body or tear the seat covers. 1. axle bracket, 6x1.0 mm, 9.8 Nm (1.0 kgf/m); 2. seat belt buckle; 3. right seat back; 4. axle bracket cover; 5. Central axis bracket; 6. bushing; 7. axle bracket;...

Replacing the rear seat back latch loop
Note: Avoid scratching the interior trim and adjacent components. 1. Remove the rear side trim panel ( see above ). 2. Loosen the bolts, then remove the latch loop. 3. Installation is carried out in the reverse order of...

Replacing the rear seat back latch
Note: Avoid scratching the interior trim and adjacent components. 1. Remove the rear seat back ( see above ). 2. Remove the frame from the back of the rear seat. 3. Unscrew the bolts, then remove the backrest latch. 4....

Replacing the rear seat cover
Note: Do not tear the seams or damage the seat covers. Wear protective gloves. Backrest cover 1. Remove the backrests ( see above ). 2. Remove head restraints, if equipped. 3. Loosen the screws and remove the clamp,...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

Link in different formats to this section

TEXTHTMLBB Code